Difference between revisions of "API-SSH-Configuration"

From Mupssoft Wiki
Jump to navigation Jump to search
 
Line 56: Line 56:
  
 
<p></p>
 
<p></p>
 +
 +
<h2>'''Cisco - IOS L2 v12'''</h2>Minimum* configuration:
 +
 +
'''BASIC ETHERNET CONFIGURATION - SUMMARY STEPS'''
 +
 +
1.    Switch> '''enable'''
 +
 +
2.    Switch# '''configure terminal'''
 +
 +
3.    Switch(config)# '''interface vlan 1'''
 +
 +
4.    Switch(config-if)# '''ip adress''' 172.17.33.5 255.255.255.0
 +
 +
5.    Switch(config-if)# '''exit'''
 +
 +
6.    Switch(config)# '''ip default-gateway''' 172.17.33.1
 +
 +
'''BASIC SSH CONFIGURATION - SUMMARY STEPS'''
 +
 +
7.    Switch(config)# '''ip domain name''' domain.local
 +
 +
8.    Switch(config)# '''hostname''' MBSwitch
 +
 +
9.    MBSwitch(config)# '''crypto key generate rsa modulus 1024'''
 +
 +
10.    MBSwitch(config)# '''username''' ''root'' privilege 15 '''secret''' ''PassW0rd''
 +
 +
11.    MBSwitch(config)# '''aaa new-model'''
 +
 +
12.    MBSwitch(config)# '''line vty 0 4'''
 +
 +
13.    MBSwitch(config-line)# '''transport input ssh'''
 +
 +
14.    MBSwitch(config-line)# '''exit'''
 +
 +
 +
'''ADDITIONAL CONFIGURATION - SUMMARY STEPS'''
 +
 +
15.    MBSwitch(config)# '''enable secret''' PassW0rd
 +
 +
16.    MBSwitch(config)# '''service password-encryption'''
 +
 +
17.    MBSwitch(config)# '''snmp-server community public RO'''
 +
 +
18.    MBSwitch(config)# '''end'''
 +
 +
19.    MBSwitch# '''copy running-config startup-config'''
 +
 +
 +
 +
 +
 +
 +
<h2>'''Cisco - ASA'''</h2>
 +
<p>Minimum* configuration. ASA Version 8.2(5):</p>
 +
 +
'''BASIC ETHERNET CONFIGURATION - SUMMARY STEPS'''
 +
 +
1. ciscoasa> '''enable'''
 +
 +
2. ciscoasa# '''configure termina'''l
 +
 +
3. (config)# '''enable password''' ''mtigroup''
 +
 +
4. ciscoasa(config)# '''hostname''' ''MBCiscoasa''
 +
 +
5. MBCiscoasa11(config)# '''interface''' ''gigabitEthernet 0/0''
 +
 +
6. MBCiscoasa11(config-if)# '''nameif inside'''
 +
 +
7. MBCiscoasa11(config-if)# '''ip address''' ''172.18.11.11 255.255.255.0''
 +
 +
8. MBCiscoasa11(config-if)# '''no shutdown'''
 +
 +
9. MBCiscoasa11(config-if)# '''exit'''
 +
 +
10. MBCiscoasa11(config)# '''route inside''' ''0.0.0.0 0.0.0.0 172.18.11.1''
 +
 +
 +
 +
 +
 +
'''BASIC SSH CONFIGURATION - SUMMARY STEPS'''
 +
 +
11. MBCiscoasa11(config)# '''ssh''' ''172.31.10.0 255.255.255.0'' '''inside'''
 +
 +
12. MBCiscoasa11(config)# '''username''' ''mupsbox password PassW0rd privilege 15''
 +
 +
13. MBCiscoasa11(config)# '''aaa authentication ssh console LOCAL'''
 +
 +
14. MBCiscoasa11(config)# '''write'''
 +
 +
 +
 +
 +
 +
'''ADDITIONAL CONFIGURATION - SUMMARY STEPS'''
 +
 +
 +
 +
<h2>'''MikroTik'''</h2>
 +
<p>Minimum configuration for RouterOS V6 (with "zero" configuration)</p><p>'''BASIC ETHERNET CONFIGURATION - SUMMARY STEPS'''</p>
 +
 +
1. [admin@MikroTik] > '''ip address add address='''''172.17.22.4/24'' '''interface='''''ether1''
 +
 +
2. [admin@MikroTik] > '''ip route add gateway='''''172.17.22.1''
 +
 +
3. [admin@MikroTik] > '''ipv6 address add address='''2001:db8:b40:4002::4/64 '''interface='''ether1
 +
 +
4. [admin@MikroTik] > '''ipv6 route add gateway='''2001:db8:b40:4002::1
 +
 +
5. [admin@MikroTik] > '''system identity set name='''MBMikroTik
 +
 +
6. [admin@MBMikroTik] > '''ip service disable telnet,ftp,www,api'''
 +
 +
7. [admin@MBMikroTik] > '''user add name='''mupsbox '''password='''PassW0rd '''group='''full
 +
 +
8. [admin@MBMikroTik] > '''user remove admin'''<h2>'''DLink DGS'''</h2>
 +
<p>Minimum* configuration:</p>'''BASIC ETHERNET CONFIGURATION - SUMMARY STEPS'''
 +
 +
1. DGS-1210-28MP/ME:5# '''config ipif System ipaddress''' 172.17.22.2/24
 +
 +
2. DGS-1210-28MP/ME:5#'''config ipif System ipv6 ipv6address''' 2001:db8:b40:4002::2/64
 +
 +
3. DGS-1210-28MP/ME:5# '''create iproute default''' 172.17.22.1
 +
 +
4. DGS-1210-28MP/ME:5# '''create ipv6route default''' 2001:db8:b40:4002::1
 +
 +
5. DGS-1210-28MP/ME:5# '''enable ssh'''
 +
 +
6. DGS-1210-28MP/ME:5# '''enable password encryption'''
 +
 +
7. DGS-1210-28MP/ME:5# '''create account admin''' mupsbox
 +
 +
8. DGS-1210-28MP/ME:5# '''save'''
 +
 +
 +
<h2>'''Huawei AR100'''</h2>
 +
 +
Minimum* configuration:
 +
 +
'''BASIC ETHERNET CONFIGURATION - SUMMARY STEPS'''
 +
 +
1. <Huawei> '''system-view'''
 +
 +
2. [Huawei] '''interface''' ''GigabitEthernet 0/0/0''
 +
 +
3. [Huawei-GigabitEthernet0/0/0] '''undo portswitch'''
 +
 +
4. [Huawei-GigabitEthernet0/0/0] '''ip address''' ''172.17.22.5 255.255.255.0''
 +
 +
5. [Huawei-GigabitEthernet0/0/0] '''quit'''
 +
 +
6. [Huawei] '''ip route-static''' '''0.0.0.0 0.0.0.0''' ''172.17.22.1''
 +
 +
7. [Huawei] '''save'''
 +
 +
 +
 +
8. [Huawei] '''aaa'''
 +
 +
9. [Huawei-aaa] '''local-user''' mupsbox '''password cipher''' PassW0rd
 +
 +
10. [Huawei-aaa] '''local-user''' '''admin privilege level 15'''
 +
 +
11. [Huawei-aaa] '''local-user admin service-type ssh'''
 +
 +
12. [Huawei-aaa] '''quit'''
 +
 +
13. [Huawei] '''quit save'''
 +
 +
14. [Huawei] '''stelnet server enable'''
 +
 +
15. [Huawei] '''save'''
 +
 +
<h2>'''Huawei Quidway 2000,3000,5000'''</h2>
 +
 +
Minimum* configuration:
 +
 +
'''BASIC ETHERNET CONFIGURATION - SUMMARY STEPS'''
 +
 +
1. <Quidway> '''system-view'''
 +
 +
2. [Quidway]'''management-vlan 1'''
 +
 +
3. [Quidway] '''interface Vlan-interface 1'''
 +
 +
4. [Quidway-Vlan-interface1] '''ip address''' ''172.17.55.7 255.255.255.0''
 +
 +
5. [[Quidway-Vlan-interface1] '''quit'''
 +
 +
6. [Quidway] '''ip route-static''' '''0.0.0.0 0.0.0.0''' ''172.17.22.1''
 +
 +
7. [Quidway] '''save'''
 +
 +
 +
 +
'''BASIC SSH CONFIGURATION - SUMMARY STEPS'''
 +
 +
8. [Quidway] '''user-interface vty 0 4'''
 +
 +
9. [Quidway-ui-vty0-4] '''authentication-mode scheme'''
 +
 +
10. [Quidway-ui-vty0-4] '''protocol inbound ssh'''
 +
 +
11. [Quidway] '''local-user''' ''mupsbox''
 +
 +
12. [Quidway-luser-mupsbox] '''password simple''' ''PassW0rd''
 +
 +
13. [Quidway-luser-mupsbox] '''service-type ssh'''
 +
 +
14. [Quidway] '''ssh user''' ''mupsbox'' '''authentication-type password'''
 +
 +
15. [Quidway] '''rsa local-key-pair create'''
 +
 +
16. [Quidway] '''save'''
 +
 +
 +
 +
 +
<h2>'''HP Procurve'''</h2>
 +
 +
Minimum* configuration:
 +
 +
'''BASIC ETHERNET CONFIGURATION - SUMMARY STEPS'''
 +
 +
1. ProCurve Switch 2510-48# '''config'''
 +
 +
2. ProCurve Switch 2510-48(config)# '''hostname''' ''MBHP-2510''
 +
 +
3. MBHP-2510(config)# '''vlan 1'''
 +
 +
4. MBHP-2510(vlan-1)# '''ip address''' ''172.17.44.2/24''
 +
 +
5. MBHP-2510(vlan-1)# '''exit'''
 +
 +
6. MBHP-2510(config)# '''ip default-gateway''' ''172.17.44.1''
 +
 +
 +
 +
 +
 +
'''BASIC SSH CONFIGURATION - SUMMARY STEPS'''
 +
 +
7. MBHP-2510(config)# '''ip ssh'''
 +
 +
8. MBHP-2510(config)# '''crypto key generate ssh'''
 +
 +
9. MBHP-2510(config)# '''password manager'''
 +
 +
10. MBHP-2510(config)# '''aaa authentication login privilege-mode'''
 +
 +
11. MBHP-2510(config)# '''aaa authentication ssh login tacacs local'''
 +
 +
12. MBHP-2510(config)# '''aaa authentication ssh enable tacacs local'''
 +
 +
13. MBHP-2510(config)# '''write memory'''
 +
 +
 +
<h2>'''Juniper SRX'''</h2>
 +
 +
Minimum* configuration:
 +
 +
'''BASIC CONFIGURATION - SUMMARY STEPS'''
 +
 +
1. root@% '''cli'''
 +
 +
2. root> '''configure'''
 +
 +
3. root# '''set system host-name''' ''MBSRX100b''
 +
 +
4. root# <kbd>'''set system root-authentication plain-text-password'''</kbd>
 +
 +
''New password: <var>password</var>''
 +
 +
''Retype new password: <var>password</var>''
 +
 +
5. root# <kbd>'''set system login user''' ''mupsbox'' '''class super-user authentication plain-text-password'''</kbd>
 +
 +
6. root# '''commit'''
 +
 +
 +
 +
'''BASIC ETHERNET CONFIGURATION - SUMMARY STEPS'''
 +
 +
7. root@MBSRX100b#  '''set interfaces''' ''fe-0/0/0'' '''unit 0 family inet address''' <var>172.17.44.4/24</var>
 +
 +
8. root@MBSRX100b# '''set routing-options static route''' '''0.0.0.0/0 next-hop''' 172.17.44.1
 +
 +
9. root@MBSRX100b# '''delete security zones security-zone untrust interfaces''' ''fe-0/0/0''
 +
 +
10. root@MBSRX100b# '''set security zones security-zone internal interfaces''' ''fe-0/0/0'' '''host-inbound-traffic system-services ping'''
 +
 +
11. root@MBSRX100b# '''set security zones security-zone internal interfaces''' ''fe-0/0/0'' '''host-inbound-traffic system-services ssh'''
 +
 +
12. root@MBSRX100b# '''set system services ssh'''
 +
 +
13. root@MBSRX100b# '''set system services ssh root-login allow'''
 +
 +
12. root@MBSRX100b# '''commit'''
 +
 +
 +
<h2>'''Juniper ES'''</h2>
 +
 +
Minimum* configuration:
 +
 +
'''BASIC CONFIGURATION - SUMMARY STEPS'''
 +
 +
1. root@% '''cli'''
 +
 +
2. root> '''configure'''
 +
 +
3. root# '''set system host-name''' MBSRX100b
 +
 +
4. root# <kbd>'''set system root-authentication plain-text-password'''</kbd>
 +
 +
''New password: <var>password</var>''
 +
 +
''Retype new password: <var>password</var>''
 +
 +
5. root# <kbd>'''set system login user''' ''mupsbox'' '''class super-user authentication plain-text-password'''</kbd>
 +
 +
6. root# '''commit'''
 +
 +
 +
 +
'''BASIC ETHERNET CONFIGURATION - SUMMARY STEPS'''
 +
 +
7. root@MBSRX100b#  delete interface ge-0/0/0 unit 0 family ethernet-switching
 +
 +
8. root@MBSRX100b#  '''set interfaces''' ge-0/0/0 '''unit 0 family inet address''' <var>172.17.44.4/24</var>
 +
 +
9. root@MBSRX100b# '''set routing-options static route''' '''0.0.0.0/0 next-hop''' 172.17.44.1
 +
 +
10. root@MBSRX100b# '''set system services ssh'''
 +
 +
11. root@MBSRX100b# '''set system services ssh connection-limit 10 rate-limit 4'''
 +
 +
12. root@MBSRX100b# '''commit'''
 +
 +
 +
 +
<h2>'''Juniper SSG'''</h2>
 +
 +
Minimum* configuration:
 +
 +
'''BASIC  CONFIGURATION - SUMMARY STEPS'''
 +
 +
1. root-> '''set hostname''' ''MBSSG5''
 +
 +
2. MBSSG5-> '''set admin name''' ''mupsbox''
 +
 +
3. MBSSG5-> '''set admin password''' ''PassW0rd''
 +
 +
4. MBSSG5-> <kbd>'''set interface''' ''bgroup0'' '''ip 172.17.44.5/24'''</kbd>
 +
 +
5. MBSSG5-> '''set route''' ''0.0.0.0/0'' '''interface''' ''bgroup0'' '''gateway''' ''172.17.44.1''
 +
 +
6. MBSSG5-> '''save'''
 +
 +
7. MBSSG5-> '''set interface''' ''bgroup0'' '''manage ssh'''
 +
 +
8. MBSSG5-> '''set ssh enable'''
 +
 +
 +
 +
 +
<h2>'''Eltex  MES'''</h2>
 +
 +
Minimum* configuration:
 +
 +
'''BASIC  CONFIGURATION - SUMMARY STEPS'''
 +
 +
1. console> '''enable'''
 +
 +
2. console# '''configure'''
 +
 +
2. console(config)# '''interface vlan 1'''
 +
 +
3. console(config-if)# '''no ip address dhcp'''
 +
 +
4. console(config-if)# '''ip address''' ''172.17.55.4 255.255.255.0''
 +
 +
5. console(config-if)# '''exit'''
 +
 +
6. console(config)# '''ip route''' ''0.0.0.0 0.0.0.0 172.17.55.1''
 +
 +
7. console(config)# '''hostname''' ''MBEltexMES''
 +
 +
8. console(config)# '''ip ssh server'''
 +
 +
9. MBEltexMES(config)# '''username''' ''mupsbox'' ''privilege 15'' '''password''' ''PassW0rd!''
 +
 +
10. MBEltexMES(config)# '''enable password prpassword'''
 +
 +
 +
 +
 +
<h2>'''Zyxel ZyWALL'''</h2>
 +
 +
Minimum* configuration:
 +
 +
'''BASIC  CONFIGURATION - SUMMARY STEPS'''
 +
 +
1. Router> '''enable'''
 +
 +
2. Router# '''configure terminal'''
 +
 +
2. Router(config)# '''interface''' ''ge2''
 +
 +
3. Router(config-if-ge)# '''ip address''' ''172.17.44.7 255.255.255.0''
 +
 +
4. Router(config-if-ge)# '''ip gateway''' ''172.17.44.1''
 +
 +
5. Router(config-if-ge)# '''no shutdown'''
 +
 +
6. Router(config-if-ge)# '''exit'''
 +
 +
7. Router(config)# '''username''' ''mupsbox'' '''password''' ''PassW0rd'' '''user-type''' ''admin''
 +
 +
 +
 +
 +
<h2>'''Qtech QSW'''</h2>
 +
 +
Minimum* configuration:
 +
 +
'''BASIC  CONFIGURATION - SUMMARY STEPS'''
 +
 +
1. QSW-2850-28T-AC> '''enable'''
 +
 +
2. QSW-2850-28T-AC# '''config terminal'''
 +
 +
2. QSW-2850-28T-AC(config)# '''interface vlan 1'''
 +
 +
3. QSW-2850-28T-AC(config-if-vlan1)# '''ip address''' ''172.17.44.8 255.255.255.0''
 +
 +
4. QSW-2850-28T-AC(config-if-vlan1)# '''exit'''
 +
 +
5. QSW-2850-28T-AC(config)# '''ip default-gateway''' ''172.17.44.1''
 +
 +
6. QSW-2850-28T-AC(config)# '''ssh-server enable'''
 +
 +
7. QSW-2850-28T-AC(config)# '''username''' ''mupsbox'' privilege 15 '''password''' ''PassW0rd''
 +
 +
8. QSW-2850-28T-AC(config)# '''exit'''
 +
 +
9. QSW-2850-28T-AC# '''copy running-config startup-config'''
 +
 +
 +
 +
 +
<h2>'''Allied Telesis'''</h2>
 +
 +
Minimum* configuration:
 +
 +
'''BASIC  CONFIGURATION - SUMMARY STEPS'''
 +
 +
1. console# '''config'''
 +
 +
2. console(config)# '''interface vlan 1'''
 +
 +
3. console(config-if)# '''ip address''' ''172.17.55.9 255.255.255.0''
 +
 +
4.console(config-if)# '''exit'''
 +
 +
5. console(config)# '''ip default-gateway''' ''172.17.55.1''
 +
 +
6. console(config)# '''username''' ''mupsbox'' '''password''' ''PassW0rd'' level 15
 +
 +
7. console(config)# '''ip ssh server'''
 +
 +
8. console(config)# '''crypto key generate rsa'''
 +
 +
 +
 +
<h2>'''Fortinet'''</h2>
 +
 +
Minimum* configuration:
 +
 +
'''BASIC  CONFIGURATION - SUMMARY STEPS'''
 +
 +
1. FortiGate-VM64-KVM # '''config system interface'''
 +
 +
2. FortiGate-VM64-KVM (interface) # '''edit''' ''port1''
 +
 +
2. FortiGate-VM64-KVM (port1) # '''set ip''' ''172.18.33.111 255.255.255.0''
 +
 +
3 FortiGate-VM64-KVM (port1) # '''end'''
 +
 +
4. FortiGate-VM64-KVM # '''config router static'''
 +
 +
5. FortiGate-VM64-KVM (static) # '''edit''' ''0''
 +
 +
6. FortiGate-VM64-KVM (0) # '''set gateway''' ''172.18.33.1''
 +
 +
7. FortiGate-VM64-KVM (0) # '''set device''' ''port1''
 +
 +
8. FortiGate-VM64-KVM (0) # '''end'''
 +
 +
9. FortiGate-VM64-KVM # '''config system admin'''
 +
 +
10. FortiGate-VM64-KVM (admin) # '''edit''' ''mupsbox''
 +
 +
11. FortiGate-VM64-KVM (mupsbox) # '''set accprofile''' ''"super_admin"''
 +
 +
12. FortiGate-VM64-KVM (mupsbox) # '''set vdom "root"'''
 +
 +
13. FortiGate-VM64-KVM (mupsbox) # '''set password''' ''PassW0rd''
 +
 +
14. FortiGate-VM64-KVM (mupsbox) # '''end'''
 +
 +
15. FortiGate-VM64-KVM # '''config system global'''
 +
 +
16. FortiGate-VM64-KVM (global) # '''set hostname''' ''FortiGateV''
 +
 +
17. FortiGate-VM64-KVM (global) # '''end'''
 +
 +
18. FortiGateV # '''execute cfg save'''
 +
 +
 +
 +
<h2>'''Extreme Networks'''</h2>
 +
 +
Minimum* configuration:
 +
 +
'''BASIC  CONFIGURATION - SUMMARY STEPS'''
 +
 +
1. * EXOS-VM.1 # '''create account admin''' ''mupsbox'' ''PassW0rd''
 +
 +
2. * EXOS-VM.6 # '''configure''' ''Mgmt'' '''ipaddress''' ''172.18.33.222 255.255.255.0''
 +
 +
3. * EXOS-VM.9 # '''configure iproute add default''' ''172.18.33.1'' '''vr''' ''VR-Mgmt''
 +
 +
4.* EXOS-VM.11 # '''enable ssh2'''
 +
 +
5.* EXOS-VM.11 # '''save'''
 +
 +
 +
 +
 +
<h2>'''Check Point'''</h2>
 +
 +
Minimum* configuration:
 +
 +
'''BASIC  CONFIGURATION - SUMMARY STEPS'''
 +
 +
1. gw-170003>set expert-password
 +
 +
2.gw-170003>expert
 +
 +
3. [Expert@gw-170003:0]# hostname MBCheckPoint
 +
 +
4.[Expert@MBCheckPoint]# hostname MBCheckPoint
 +
 +
5.* EXOS-VM.11 # save
 +
 +
  
  

Latest revision as of 04:49, 22 June 2021

Device Configuration

Introduction

This section is not a tutorial on configuration different manufacturers. Here you will find the minimum settings in the CLI (for access from MUPSBOX to devices).


Cisco - IOS v15

Minimum* configuration:

BASIC ETHERNET CONFIGURATION - SUMMARY STEPS

1. Router> enable

2. Router# configure terminal

3. Router(config)# interface gigabitethernet 0/0

4. Router(config-if)# ip adress 10.9.90.201 255.255.255.0

5. Router(config-if)# ipv6 address 2001:db8:B40:4000::101/64

6. Router(config-if)# no shutdown

7. Router(config-if)# exit

8. Router(config)# ip route 0.0.0.0 0.0.0.0 10.9.90.1

9. Router(config)# ipv6 route ::/0 2001:db8:B40:4000::1

BASIC SSH CONFIGURATION - SUMMARY STEPS

10. Router(config)# ip domain name domain.local

11. Router(config)# hostname MBRouter

12. MBRouter(config)# crypto key generate rsa modulus 1024

13. MBRouter(config)# username root privilege 15 secret PassW0rd

14. MBRouter(config)# aaa new-model

15. MBRouter(config)# line vty 0 4

16. MBRouter(config-line)# transport input ssh

17. MBRouter(config-line)# exit

ADDITIONAL CONFIGURATION - SUMMARY STEPS

18. MBRouter(config)# enable secret PassW0rd

19. MBRouter(config)# service password-encryption

20. MBRouter(config)# end

21. MBRouter# copy running-config startup-config


Cisco - IOS L2 v12

Minimum* configuration:

BASIC ETHERNET CONFIGURATION - SUMMARY STEPS

1. Switch> enable

2. Switch# configure terminal

3. Switch(config)# interface vlan 1

4. Switch(config-if)# ip adress 172.17.33.5 255.255.255.0

5. Switch(config-if)# exit

6. Switch(config)# ip default-gateway 172.17.33.1

BASIC SSH CONFIGURATION - SUMMARY STEPS

7. Switch(config)# ip domain name domain.local

8. Switch(config)# hostname MBSwitch

9. MBSwitch(config)# crypto key generate rsa modulus 1024

10. MBSwitch(config)# username root privilege 15 secret PassW0rd

11. MBSwitch(config)# aaa new-model

12. MBSwitch(config)# line vty 0 4

13. MBSwitch(config-line)# transport input ssh

14. MBSwitch(config-line)# exit


ADDITIONAL CONFIGURATION - SUMMARY STEPS

15. MBSwitch(config)# enable secret PassW0rd

16. MBSwitch(config)# service password-encryption

17. MBSwitch(config)# snmp-server community public RO

18. MBSwitch(config)# end

19. MBSwitch# copy running-config startup-config




Cisco - ASA

Minimum* configuration. ASA Version 8.2(5):

BASIC ETHERNET CONFIGURATION - SUMMARY STEPS

1. ciscoasa> enable

2. ciscoasa# configure terminal

3. (config)# enable password mtigroup

4. ciscoasa(config)# hostname MBCiscoasa

5. MBCiscoasa11(config)# interface gigabitEthernet 0/0

6. MBCiscoasa11(config-if)# nameif inside

7. MBCiscoasa11(config-if)# ip address 172.18.11.11 255.255.255.0

8. MBCiscoasa11(config-if)# no shutdown

9. MBCiscoasa11(config-if)# exit

10. MBCiscoasa11(config)# route inside 0.0.0.0 0.0.0.0 172.18.11.1



BASIC SSH CONFIGURATION - SUMMARY STEPS

11. MBCiscoasa11(config)# ssh 172.31.10.0 255.255.255.0 inside

12. MBCiscoasa11(config)# username mupsbox password PassW0rd privilege 15

13. MBCiscoasa11(config)# aaa authentication ssh console LOCAL

14. MBCiscoasa11(config)# write



ADDITIONAL CONFIGURATION - SUMMARY STEPS


MikroTik

Minimum configuration for RouterOS V6 (with "zero" configuration)

BASIC ETHERNET CONFIGURATION - SUMMARY STEPS

1. [admin@MikroTik] > ip address add address=172.17.22.4/24 interface=ether1

2. [admin@MikroTik] > ip route add gateway=172.17.22.1

3. [admin@MikroTik] > ipv6 address add address=2001:db8:b40:4002::4/64 interface=ether1

4. [admin@MikroTik] > ipv6 route add gateway=2001:db8:b40:4002::1

5. [admin@MikroTik] > system identity set name=MBMikroTik

6. [admin@MBMikroTik] > ip service disable telnet,ftp,www,api

7. [admin@MBMikroTik] > user add name=mupsbox password=PassW0rd group=full

8. [admin@MBMikroTik] > user remove admin

DLink DGS

Minimum* configuration:

BASIC ETHERNET CONFIGURATION - SUMMARY STEPS

1. DGS-1210-28MP/ME:5# config ipif System ipaddress 172.17.22.2/24

2. DGS-1210-28MP/ME:5#config ipif System ipv6 ipv6address 2001:db8:b40:4002::2/64

3. DGS-1210-28MP/ME:5# create iproute default 172.17.22.1

4. DGS-1210-28MP/ME:5# create ipv6route default 2001:db8:b40:4002::1

5. DGS-1210-28MP/ME:5# enable ssh

6. DGS-1210-28MP/ME:5# enable password encryption

7. DGS-1210-28MP/ME:5# create account admin mupsbox

8. DGS-1210-28MP/ME:5# save


Huawei AR100

Minimum* configuration:

BASIC ETHERNET CONFIGURATION - SUMMARY STEPS

1. <Huawei> system-view

2. [Huawei] interface GigabitEthernet 0/0/0

3. [Huawei-GigabitEthernet0/0/0] undo portswitch

4. [Huawei-GigabitEthernet0/0/0] ip address 172.17.22.5 255.255.255.0

5. [Huawei-GigabitEthernet0/0/0] quit

6. [Huawei] ip route-static 0.0.0.0 0.0.0.0 172.17.22.1

7. [Huawei] save


8. [Huawei] aaa

9. [Huawei-aaa] local-user mupsbox password cipher PassW0rd

10. [Huawei-aaa] local-user admin privilege level 15

11. [Huawei-aaa] local-user admin service-type ssh

12. [Huawei-aaa] quit

13. [Huawei] quit save

14. [Huawei] stelnet server enable

15. [Huawei] save

Huawei Quidway 2000,3000,5000

Minimum* configuration:

BASIC ETHERNET CONFIGURATION - SUMMARY STEPS

1. <Quidway> system-view

2. [Quidway]management-vlan 1

3. [Quidway] interface Vlan-interface 1

4. [Quidway-Vlan-interface1] ip address 172.17.55.7 255.255.255.0

5. [[Quidway-Vlan-interface1] quit

6. [Quidway] ip route-static 0.0.0.0 0.0.0.0 172.17.22.1

7. [Quidway] save


BASIC SSH CONFIGURATION - SUMMARY STEPS

8. [Quidway] user-interface vty 0 4

9. [Quidway-ui-vty0-4] authentication-mode scheme

10. [Quidway-ui-vty0-4] protocol inbound ssh

11. [Quidway] local-user mupsbox

12. [Quidway-luser-mupsbox] password simple PassW0rd

13. [Quidway-luser-mupsbox] service-type ssh

14. [Quidway] ssh user mupsbox authentication-type password

15. [Quidway] rsa local-key-pair create

16. [Quidway] save



HP Procurve

Minimum* configuration:

BASIC ETHERNET CONFIGURATION - SUMMARY STEPS

1. ProCurve Switch 2510-48# config

2. ProCurve Switch 2510-48(config)# hostname MBHP-2510

3. MBHP-2510(config)# vlan 1

4. MBHP-2510(vlan-1)# ip address 172.17.44.2/24

5. MBHP-2510(vlan-1)# exit

6. MBHP-2510(config)# ip default-gateway 172.17.44.1



BASIC SSH CONFIGURATION - SUMMARY STEPS

7. MBHP-2510(config)# ip ssh

8. MBHP-2510(config)# crypto key generate ssh

9. MBHP-2510(config)# password manager

10. MBHP-2510(config)# aaa authentication login privilege-mode

11. MBHP-2510(config)# aaa authentication ssh login tacacs local

12. MBHP-2510(config)# aaa authentication ssh enable tacacs local

13. MBHP-2510(config)# write memory


Juniper SRX

Minimum* configuration:

BASIC CONFIGURATION - SUMMARY STEPS

1. root@% cli

2. root> configure

3. root# set system host-name MBSRX100b

4. root# set system root-authentication plain-text-password

New password: password

Retype new password: password

5. root# set system login user mupsbox class super-user authentication plain-text-password

6. root# commit


BASIC ETHERNET CONFIGURATION - SUMMARY STEPS

7. root@MBSRX100b# set interfaces fe-0/0/0 unit 0 family inet address 172.17.44.4/24

8. root@MBSRX100b# set routing-options static route 0.0.0.0/0 next-hop 172.17.44.1

9. root@MBSRX100b# delete security zones security-zone untrust interfaces fe-0/0/0

10. root@MBSRX100b# set security zones security-zone internal interfaces fe-0/0/0 host-inbound-traffic system-services ping

11. root@MBSRX100b# set security zones security-zone internal interfaces fe-0/0/0 host-inbound-traffic system-services ssh

12. root@MBSRX100b# set system services ssh

13. root@MBSRX100b# set system services ssh root-login allow

12. root@MBSRX100b# commit


Juniper ES

Minimum* configuration:

BASIC CONFIGURATION - SUMMARY STEPS

1. root@% cli

2. root> configure

3. root# set system host-name MBSRX100b

4. root# set system root-authentication plain-text-password

New password: password

Retype new password: password

5. root# set system login user mupsbox class super-user authentication plain-text-password

6. root# commit


BASIC ETHERNET CONFIGURATION - SUMMARY STEPS

7. root@MBSRX100b# delete interface ge-0/0/0 unit 0 family ethernet-switching

8. root@MBSRX100b# set interfaces ge-0/0/0 unit 0 family inet address 172.17.44.4/24

9. root@MBSRX100b# set routing-options static route 0.0.0.0/0 next-hop 172.17.44.1

10. root@MBSRX100b# set system services ssh

11. root@MBSRX100b# set system services ssh connection-limit 10 rate-limit 4

12. root@MBSRX100b# commit


Juniper SSG

Minimum* configuration:

BASIC CONFIGURATION - SUMMARY STEPS

1. root-> set hostname MBSSG5

2. MBSSG5-> set admin name mupsbox

3. MBSSG5-> set admin password PassW0rd

4. MBSSG5-> set interface bgroup0 ip 172.17.44.5/24

5. MBSSG5-> set route 0.0.0.0/0 interface bgroup0 gateway 172.17.44.1

6. MBSSG5-> save

7. MBSSG5-> set interface bgroup0 manage ssh

8. MBSSG5-> set ssh enable



Eltex MES

Minimum* configuration:

BASIC CONFIGURATION - SUMMARY STEPS

1. console> enable

2. console# configure

2. console(config)# interface vlan 1

3. console(config-if)# no ip address dhcp

4. console(config-if)# ip address 172.17.55.4 255.255.255.0

5. console(config-if)# exit

6. console(config)# ip route 0.0.0.0 0.0.0.0 172.17.55.1

7. console(config)# hostname MBEltexMES

8. console(config)# ip ssh server

9. MBEltexMES(config)# username mupsbox privilege 15 password PassW0rd!

10. MBEltexMES(config)# enable password prpassword



Zyxel ZyWALL

Minimum* configuration:

BASIC CONFIGURATION - SUMMARY STEPS

1. Router> enable

2. Router# configure terminal

2. Router(config)# interface ge2

3. Router(config-if-ge)# ip address 172.17.44.7 255.255.255.0

4. Router(config-if-ge)# ip gateway 172.17.44.1

5. Router(config-if-ge)# no shutdown

6. Router(config-if-ge)# exit

7. Router(config)# username mupsbox password PassW0rd user-type admin



Qtech QSW

Minimum* configuration:

BASIC CONFIGURATION - SUMMARY STEPS

1. QSW-2850-28T-AC> enable

2. QSW-2850-28T-AC# config terminal

2. QSW-2850-28T-AC(config)# interface vlan 1

3. QSW-2850-28T-AC(config-if-vlan1)# ip address 172.17.44.8 255.255.255.0

4. QSW-2850-28T-AC(config-if-vlan1)# exit

5. QSW-2850-28T-AC(config)# ip default-gateway 172.17.44.1

6. QSW-2850-28T-AC(config)# ssh-server enable

7. QSW-2850-28T-AC(config)# username mupsbox privilege 15 password PassW0rd

8. QSW-2850-28T-AC(config)# exit

9. QSW-2850-28T-AC# copy running-config startup-config



Allied Telesis

Minimum* configuration:

BASIC CONFIGURATION - SUMMARY STEPS

1. console# config

2. console(config)# interface vlan 1

3. console(config-if)# ip address 172.17.55.9 255.255.255.0

4.console(config-if)# exit

5. console(config)# ip default-gateway 172.17.55.1

6. console(config)# username mupsbox password PassW0rd level 15

7. console(config)# ip ssh server

8. console(config)# crypto key generate rsa


Fortinet

Minimum* configuration:

BASIC CONFIGURATION - SUMMARY STEPS

1. FortiGate-VM64-KVM # config system interface

2. FortiGate-VM64-KVM (interface) # edit port1

2. FortiGate-VM64-KVM (port1) # set ip 172.18.33.111 255.255.255.0

3 FortiGate-VM64-KVM (port1) # end

4. FortiGate-VM64-KVM # config router static

5. FortiGate-VM64-KVM (static) # edit 0

6. FortiGate-VM64-KVM (0) # set gateway 172.18.33.1

7. FortiGate-VM64-KVM (0) # set device port1

8. FortiGate-VM64-KVM (0) # end

9. FortiGate-VM64-KVM # config system admin

10. FortiGate-VM64-KVM (admin) # edit mupsbox

11. FortiGate-VM64-KVM (mupsbox) # set accprofile "super_admin"

12. FortiGate-VM64-KVM (mupsbox) # set vdom "root"

13. FortiGate-VM64-KVM (mupsbox) # set password PassW0rd

14. FortiGate-VM64-KVM (mupsbox) # end

15. FortiGate-VM64-KVM # config system global

16. FortiGate-VM64-KVM (global) # set hostname FortiGateV

17. FortiGate-VM64-KVM (global) # end

18. FortiGateV # execute cfg save


Extreme Networks

Minimum* configuration:

BASIC CONFIGURATION - SUMMARY STEPS

1. * EXOS-VM.1 # create account admin mupsbox PassW0rd

2. * EXOS-VM.6 # configure Mgmt ipaddress 172.18.33.222 255.255.255.0

3. * EXOS-VM.9 # configure iproute add default 172.18.33.1 vr VR-Mgmt

4.* EXOS-VM.11 # enable ssh2

5.* EXOS-VM.11 # save



Check Point

Minimum* configuration:

BASIC CONFIGURATION - SUMMARY STEPS

1. gw-170003>set expert-password

2.gw-170003>expert

3. [Expert@gw-170003:0]# hostname MBCheckPoint

4.[Expert@MBCheckPoint]# hostname MBCheckPoint

5.* EXOS-VM.11 # save






Retrieved from "https://wiki.mupssoft.com/index.php?title=API-SSH-Configuration&oldid=1087"