Device Configuration

Introduction

This section is not a tutorial on configuration different manufacturers. Here you will find the minimum settings in the CLI (for access from MUPSBOX to devices).

Vendor Configuration

Cisco - IOS v15

Minimum* configuration:

BASIC ETHERNET CONFIGURATION - SUMMARY STEPS

1. Router> enable

2. Router# configure terminal

3. Router(config)# interface gigabitethernet 0/0

4. Router(config-if)# ip adress 10.9.90.201 255.255.255.0

5. Router(config-if)# ipv6 address 2001:db8:B40:4000::101/64

6. Router(config-if)# no shutdown

7. Router(config-if)# exit

8. Router(config)# ip route 0.0.0.0 0.0.0.0 10.9.90.1

9. Router(config)# ipv6 route ::/0 2001:db8:B40:4000::1

BASIC SSH CONFIGURATION - SUMMARY STEPS

10. Router(config)# ip domain name domain.local

11. Router(config)# hostname MBRouter

12. MBRouter(config)# crypto key generate rsa modulus 1024

13. MBRouter(config)# username root privilege 15 secret PassW0rd

14. MBRouter(config)# aaa new-model

15. MBRouter(config)# line vty 0 4

16. MBRouter(config-line)# transport input ssh

MBRouter(config-line)# exit

ADDITIONAL CONFIGURATION - SUMMARY STEPS

17. MBRouter(config)# enable secret PassW0rd

18. MBRouter(config)# service password-encryption

19. MBRouter(config)# end

20. MBRouter# copy running-config startup-config

BASIC ETHERNET CONFIGURATION - DETAILED STEPS
	Comman or Action	Purpose
Step 1	enable Example: Router> enable	Enables privileged EXEC mode. Enter your password if prompted.
Step 2	configure terminal Example: Router# configure terminal	Enters global configuration mode.
Step 3	interface gigabitethernet slot/port Example: Router(config)# interface gigabitethernet 0/0	Specify the port adapter type and the location of the interface to be configured.
Step 4	ip address ip subnetmask Example: Router(config-if)# ip address 10.9.90.201 255.255.255.0	Sets the IPv4 address and subnet mask for the specified GE interface.
Step 5	ipv6 address ip/prefix Example: Router(config-if)# ipv6 address 2001:db8:B40:4000::101/64	Sets the IPv6 address and prefix for the specified GE interface
Step 6	no shutdown Example: Router(config-if)# no shutdown	Enables the GE interface, changing its state from administratively down to administratively up
Step 7	exit Example: Router(config-if)# exit	Exits configuration mode for the GE interface and returns to global configuration mode.
Step 8	ip route 0.0.0.0 0.0.0.0 gateway Example: Router(config)# ip route 0.0.0.0 0.0.0.0 10.9.90.1	Add route - default gateway for IPv4
Step 9	ipv6 route ::/0 gateway Example: Router(config)# ipv6 route ::/0 2001:db8:B40:4000::1	Add route - default gateway for IPv6

BASIC SSH CONFIG - DETAILED STEPS
	Comman or Action	Purpose
Step 10	ip domain name domain name Example: Router(config)# ip domain name domain.local	Specifies the default domain name that Cisco IOS software uses to complete unqualified host names
Step 11	hostname newhostname Example: Router(config)# hostname MBRouter	Specifies the name for the router.
Step 12	crypto key generate rsa modulus 1024 Example: MBRouter(config)# crypto key generate rsa modulus 1024	To generate Rivest, Shamir, and Adelman (RSA) key pairs.
Step 13	username root privilege 15 secret PassW0rd Example: MBRouter(config)# username root privilege 15 secret PassW0rd	Specifies the secret for the root.
Step 14	aaa new-model Example: MBRouter(config)# aaa new-model	Enable AAA on router.
Step 15	line vty 0 4 Example: MBRouter(config)# line vty 0 4	Entering the configuration mode VTY is a virtual port and used to get Telnet or SSH access to the device.
Step 16	transport input ssh Example: MBRouter(config-line)# transport input ssh MBRouter(config-line)# exit	Accept only ssh via vty line.

ADDITIONAL CONFIG - DETAILED STEPS
	Comman or Action	Purpose
Step 17	enable secret PassW0rd Example: MBRouter(config)# enable secret PassW0rd	Defines a new password or changes an existing password for access to privileged EXEC mode.
Step 18	service password-encryption Example: MBRouter(config)# service password-encryption	(Optional) Encrypts the password when the password is defined or when the configuration is written Encryption prevents the password from being readable in the configuration file.
Step 19	end Example: MBRouter(config)# end	Exits global configuration mode and returns to privileged EXEC mode.
Step 20	copy running-config startup-config Example: MBrouter# copy running-config startup-config	Saves the running configuration file as the startup configuration file.

MupsBox will sort the data and display only the values found. These data can be exported to Excel for further processing.

Cisco - ASA

Minimum* configuration. ASA Version 8.2(5):

BASIC ETHERNET CONFIGURATION - SUMMARY STEPS

1. Switch> enable

2. Switch# configure terminal

3. Switch(config)# interface gigabitethernet 0/0

4. Switch(config-if)# no switchport

5. Switch(config-if)# ip adress 10.9.90.201 255.255.255.0

6. Switch(config-if)# exit

7. Switch(config)# ip route 0.0.0.0 0.0.0.0 10.9.90.1

BASIC SSH CONFIGURATION - SUMMARY STEPS

8. Router(config)# ip domain name domain.local

9. Router(config)# hostname MBRouter

10. MBRouter(config)# crypto key generate rsa modulus 1024

11. MBRouter(config)# username root privilege 15 secret PassW0rd

12. MBRouter(config)# aaa new-model

13. MBRouter(config)# line vty 0 4

14. MBRouter(config-line)# transport input ssh

MBRouter(config-line)# exit

ADDITIONAL CONFIGURATION - SUMMARY STEPS

15. MBRouter(config)# enable secret PassW0rd

16. MBRouter(config)# service password-encryption

17. MBRouter(config)# end

18. MBRouter# copy running-config startup-config

BASIC ETHERNET CONFIGURATION - DETAILED STEPS
	Comman or Action	Purpose
Step 1	enable Example: Router> enable	Enables privileged EXEC mode. Enter your password if prompted.
Step 2	configure terminal Example: Router# configure terminal	Enters global configuration mode.
Step 3	interface gigabitethernet slot/port Example: Router(config)# interface gigabitethernet 0/0	Specify the port adapter type and the location of the interface to be configured.
Step 4	ip address ip subnetmask Example: Router(config-if)# ip address 10.9.90.201 255.255.255.0	Sets the IP address and subnet mask for the specified GE interface.
Step 5	no shutdown Example: Router(config-if)# no shutdown	Enables the GE interface, changing its state from administratively down to administratively up
Step 6	exit Example: Router(config-if)# exit	Exits configuration mode for the GE interface and returns to global configuration mode.
Step 7	ip route 0.0.0.0 0.0.0.0 gateway Example: Router(config)# ip route 0.0.0.0 0.0.0.0 10.9.90.1	Add route - default gateway

BASIC SSH CONFIG - DETAILED STEPS
	Comman or Action	Purpose
Step 8	ip domain name domain name Example: Router(config)# ip domain name domain.local	Specifies the default domain name that Cisco IOS software uses to complete unqualified host names
Step 9	hostname newhostname Example: Router(config)# hostname MBRouter	Specifies the name for the router.
Step 10	crypto key generate rsa modulus 1024 Example: MBRouter(config)# crypto key generate rsa modulus 1024	To generate Rivest, Shamir, and Adelman (RSA) key pairs.
Step 11	username root privilege 15 secret PassW0rd Example: MBRouter(config)# username root privilege 15 secret PassW0rd	Specifies the secret for the root.
Step 12	aaa new-model Example: MBRouter(config)# aaa new-model	Enable AAA on router.
Step 13	line vty 0 4 Example: MBRouter(config)# line vty 0 4	Entering the configuration mode VTY is a virtual port and used to get Telnet or SSH access to the device.
Step 14	transport input ssh Example: MBRouter(config-line)# transport input ssh MBRouter(config-line)# exit	Accept only ssh via vty line.

ADDITIONAL CONFIG - DETAILED STEPS
	Comman or Action	Purpose
Step 15	enable secret PassW0rd Example: MBRouter(config)# enable secret PassW0rd	Defines a new password or changes an existing password for access to privileged EXEC mode.
Step 16	service password-encryption Example: MBRouter(config)# service password-encryption	(Optional) Encrypts the password when the password is defined or when the configuration is written Encryption prevents the password from being readable in the configuration file.
Step 17	end Example: MBRouter(config)# end	Exits global configuration mode and returns to privileged EXEC mode.
Step 18	copy running-config startup-config Example: MBrouter# copy running-config startup-config	Saves the running configuration file as the startup configuration file.

MikroTik

Minimum configuration for RouterOS V6

DLink DGS

Minimum* configuration:

BASIC ETHERNET CONFIGURATION - SUMMARY STEPS

1. DGS-1210-28MP/ME:5# config ipif System ipaddress 172.17.22.2/24

2. DGS-1210-28MP/ME:5#config ipif System ipv6 ipv6address 2001:db8:b40:4002::2/64

3. DGS-1210-28MP/ME:5# create iproute default 172.17.22.1

4. DGS-1210-28MP/ME:5# create ipv6route default 2001:db8:b40:4002::1

5. DGS-1210-28MP/ME:5# enable ssh

6. DGS-1210-28MP/ME:5# enable password encryption

7. DGS-1210-28MP/ME:5# create account admin mupsbox

8. DGS-1210-28MP/ME:5# save

9. Router(config)# save

Huawei

To filter by prefix, click the down arrow in the prefix field, as shown in the figure below and select the prefix or prefixes by which you need to filter the data.