Device Configuration

Introduction

This section is not a tutorial on configuration different manufacturers. Here you will find the minimum settings in the CLI (for access from MUPSBOX to devices).

Vendor Configuration

Cisco - IOS v15

Minimum configuration:

BASIC ETHERNET CONFIGURATION - SUMMARY STEPS

1. Router> enable

2. Router# configure terminal

3. Router(config)# interface gigabitethernet 0/0

4. Router(config-if)# ip adress 10.9.90.201 255.255.255.0

5. Router(config-if)# no shutdown

6. Router(config-if)# exit

7. Router(config)# ip route 0.0.0.0 0.0.0.0 10.9.90.1

BASIC SSH CONFIGURATION - SUMMARY STEPS

8. Router(config)# ip domain name domain.local

9. Router(config)# hostname MBRouter

10. MBRouter(config)# crypto key generate rsa modulus 1024

11. MBRouter(config)# username root privilege 15 secret PassW0rd

12. MBRouter(config)# aaa new-model

13. MBRouter(config)# line vty 0 4

14. MBRouter(config-line)# transport input ssh

MBRouter(config-line)# exit

ADDITIONAL CONFIGURATION - SUMMARY STEPS

15. MBRouter(config)# enable secret PassW0rd

16. MBRouter(config)# service password-encryption

17. MBRouter(config)# end

18. MBRouter# copy running-config startup-config

BASIC ETHERNET CONFIGURATION - DETAILED STEPS
	Comman or Action	Purpose
Step 1	enable Example: Router> enable	Enables privileged EXEC mode. Enter your password if prompted.
Step 2	configure terminal Example: Router# configure terminal	Enters global configuration mode.
Step 3	interface gigabitethernet slot/port Example: Router(config)# interface gigabitethernet 0/0	Specify the port adapter type and the location of the interface to be configured.
Step 4	ip address ip subnetmask Example: Router(config-if)# ip address 10.9.90.201 255.255.255.0	Sets the IP address and subnet mask for the specified GE interface.
Step 5	no shutdown Example: Router(config-if)# no shutdown	Enables the GE interface, changing its state from administratively down to administratively up
Step 6	exit Example: Router(config-if)# exit	Exits configuration mode for the GE interface and returns to global configuration mode.
Step 7	ip route 0.0.0.0 0.0.0.0 gateway Example: Router(config)# ip route 0.0.0.0 0.0.0.0 10.9.90.1	Add route - default gateway

BASIC SSH CONFIG - DETAILED STEPS
	Comman or Action	Purpose
Step 8	ip domain name domain name Example: Router(config)# ip domain name domain.local	Specifies the default domain name that Cisco IOS software uses to complete unqualified host names
Step 9	hostname newhostname Example: Router(config)# hostname MBRouter	Specifies the name for the router.
Step 10	crypto key generate rsa modulus 1024 Example: MBRouter(config)# crypto key generate rsa modulus 1024	To generate Rivest, Shamir, and Adelman (RSA) key pairs.
Step 11	username root privilege 15 secret PassW0rd Example: MBRouter(config)# username root privilege 15 secret PassW0rd	Specifies the secret for the root.
Step 12	aaa new-model Example: MBRouter(config)# aaa new-model
Step 13	line vty 0 4 Example: MBRouter(config)# line vty 0 4
Step 14	transport input ssh Example: MBRouter(config-line)# transport input ssh MBRouter(config-line)# exit

ADDITIONAL CONFIG - DETAILED STEPS
	Comman or Action	Purpose
Step 15	enable secret PassW0rd Example: MBRouter(config)# enable secret PassW0rd	Enables privileged EXEC mode. Enter your password if prompted.
Step 16	service password-encryption Example: MBRouter(config)# service password-encryption	Enters global configuration mode.
Step 17	end Example: MBRouter(config)# end
Step 18	copy running-config startup-config Example: MBrouter# copy running-config startup-config

MupsBox will sort the data and display only the values found. These data can be exported to Excel for further processing.

Cisco - IOS L2 v15

To search for data by given dates and times, check the boxes next to them and select the date and time you are interested in:

Cisco - IOS L2 v12

To filter by prefix, click the down arrow in the prefix field, as shown in the figure below and select the prefix or prefixes by which you need to filter the data.