Difference between revisions of "Device configuration for MupsBox"
| Line 64: | Line 64: | ||
<p>MupsBox will sort the data and display only the values found. These data can be exported to Excel for further processing.</p> | <p>MupsBox will sort the data and display only the values found. These data can be exported to Excel for further processing.</p> | ||
| + | |||
| + | <h2>'''Cisco - IOS L2 v12'''</h2>Minimum* configuration: | ||
| + | |||
| + | '''BASIC ETHERNET CONFIGURATION - SUMMARY STEPS''' | ||
| + | |||
| + | 1. Router> '''enable''' | ||
| + | |||
| + | 2. Router# '''configure terminal''' | ||
| + | |||
| + | 3. Router(config)# '''interface gigabitethernet''' 0/0 | ||
| + | |||
| + | 4. Router(config-if)# '''ip adress''' 10.9.90.201 255.255.255.0 | ||
| + | |||
| + | 5. Router(config-if)# '''ipv6 address''' 2001:db8:B40:4000::101/64 | ||
| + | |||
| + | 6. Router(config-if)# '''no shutdown''' | ||
| + | |||
| + | 7. Router(config-if)# '''exit''' | ||
| + | |||
| + | 8. Router(config)# '''ip route 0.0.0.0 0.0.0.0''' 10.9.90.1 | ||
| + | |||
| + | 9. Router(config)# '''ipv6 route''' ::/0 2001:db8:B40:4000::1 | ||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | '''BASIC SSH CONFIGURATION - SUMMARY STEPS''' | ||
| + | |||
| + | 10. Router(config)# '''ip domain name''' domain.local | ||
| + | |||
| + | 11. Router(config)# '''hostname''' MBRouter | ||
| + | |||
| + | 12. MBRouter(config)# '''crypto key generate rsa modulus 1024''' | ||
| + | |||
| + | 13. MBRouter(config)# '''username''' ''root'' privilege 15 '''secret''' ''PassW0rd'' | ||
| + | |||
| + | 14. MBRouter(config)# '''aaa new-model''' | ||
| + | |||
| + | 15. MBRouter(config)# '''line vty 0 4''' | ||
| + | |||
| + | 16. MBRouter(config-line)# '''transport input ssh''' | ||
| + | |||
| + | MBRouter(config-line)# '''exit''' | ||
| + | |||
| + | |||
| + | |||
| + | '''ADDITIONAL CONFIGURATION - SUMMARY STEPS''' | ||
| + | |||
| + | 17. MBRouter(config)# '''enable secret''' PassW0rd | ||
| + | |||
| + | 18. MBRouter(config)# '''service password-encryption''' | ||
| + | |||
| + | 19. MBRouter(config)# '''end''' | ||
| + | |||
| + | 20. MBRouter# '''copy running-config startup-config''' | ||
| + | |||
| + | |||
Revision as of 23:43, 10 June 2021
Device Configuration
Introduction
This section is not a tutorial on configuration different manufacturers. Here you will find the minimum settings in the CLI (for access from MUPSBOX to devices).
Vendor Configuration
Cisco - IOS v15
Minimum* configuration:
BASIC ETHERNET CONFIGURATION - SUMMARY STEPS
1. Router> enable
2. Router# configure terminal
3. Router(config)# interface gigabitethernet 0/0
4. Router(config-if)# ip adress 10.9.90.201 255.255.255.0
5. Router(config-if)# ipv6 address 2001:db8:B40:4000::101/64
6. Router(config-if)# no shutdown
7. Router(config-if)# exit
8. Router(config)# ip route 0.0.0.0 0.0.0.0 10.9.90.1
9. Router(config)# ipv6 route ::/0 2001:db8:B40:4000::1
BASIC SSH CONFIGURATION - SUMMARY STEPS
10. Router(config)# ip domain name domain.local
11. Router(config)# hostname MBRouter
12. MBRouter(config)# crypto key generate rsa modulus 1024
13. MBRouter(config)# username root privilege 15 secret PassW0rd
14. MBRouter(config)# aaa new-model
15. MBRouter(config)# line vty 0 4
16. MBRouter(config-line)# transport input ssh
MBRouter(config-line)# exit
ADDITIONAL CONFIGURATION - SUMMARY STEPS
17. MBRouter(config)# enable secret PassW0rd
18. MBRouter(config)# service password-encryption
19. MBRouter(config)# end
20. MBRouter# copy running-config startup-config
MupsBox will sort the data and display only the values found. These data can be exported to Excel for further processing.
Cisco - IOS L2 v12
Minimum* configuration:
BASIC ETHERNET CONFIGURATION - SUMMARY STEPS
1. Router> enable
2. Router# configure terminal
3. Router(config)# interface gigabitethernet 0/0
4. Router(config-if)# ip adress 10.9.90.201 255.255.255.0
5. Router(config-if)# ipv6 address 2001:db8:B40:4000::101/64
6. Router(config-if)# no shutdown
7. Router(config-if)# exit
8. Router(config)# ip route 0.0.0.0 0.0.0.0 10.9.90.1
9. Router(config)# ipv6 route ::/0 2001:db8:B40:4000::1
BASIC SSH CONFIGURATION - SUMMARY STEPS
10. Router(config)# ip domain name domain.local
11. Router(config)# hostname MBRouter
12. MBRouter(config)# crypto key generate rsa modulus 1024
13. MBRouter(config)# username root privilege 15 secret PassW0rd
14. MBRouter(config)# aaa new-model
15. MBRouter(config)# line vty 0 4
16. MBRouter(config-line)# transport input ssh
MBRouter(config-line)# exit
ADDITIONAL CONFIGURATION - SUMMARY STEPS
17. MBRouter(config)# enable secret PassW0rd
18. MBRouter(config)# service password-encryption
19. MBRouter(config)# end
20. MBRouter# copy running-config startup-config
Cisco - ASA
Minimum* configuration. ASA Version 8.2(5):
BASIC ETHERNET CONFIGURATION - SUMMARY STEPS
1. Switch> enable
2. Switch# configure terminal
3. Switch(config)# interface gigabitethernet 0/0
4. Switch(config-if)# no switchport
5. Switch(config-if)# ip adress 10.9.90.201 255.255.255.0
6. Switch(config-if)# exit
7. Switch(config)# ip route 0.0.0.0 0.0.0.0 10.9.90.1
BASIC SSH CONFIGURATION - SUMMARY STEPS
8. Router(config)# ip domain name domain.local
9. Router(config)# hostname MBRouter
10. MBRouter(config)# crypto key generate rsa modulus 1024
11. MBRouter(config)# username root privilege 15 secret PassW0rd
12. MBRouter(config)# aaa new-model
13. MBRouter(config)# line vty 0 4
14. MBRouter(config-line)# transport input ssh
MBRouter(config-line)# exit
ADDITIONAL CONFIGURATION - SUMMARY STEPS
15. MBRouter(config)# enable secret PassW0rd
16. MBRouter(config)# service password-encryption
17. MBRouter(config)# end
18. MBRouter# copy running-config startup-config
MikroTik
Minimum configuration for RouterOS V6 (with "zero" configuration)
BASIC ETHERNET CONFIGURATION - SUMMARY STEPS
1. [admin@MikroTik] > ip address add address=172.17.22.4/24 interface=ether1
2. [admin@MikroTik] > ip route add gateway=172.17.22.1
3. [admin@MikroTik] > ipv6 address add address=2001:db8:b40:4002::4/64 interface=ether1
4. [admin@MikroTik] > ipv6 route add gateway=2001:db8:b40:4002::1
5. [admin@MikroTik] > system identity set name=MBMikroTik
6. [admin@MBMikroTik] > ip service disable telnet,ftp,www,api
7. [admin@MBMikroTik] > user add name=mupsbox password=PassW0rd group=full
8. [admin@MBMikroTik] > user remove admin
DLink DGS
Minimum* configuration:
BASIC ETHERNET CONFIGURATION - SUMMARY STEPS
1. DGS-1210-28MP/ME:5# config ipif System ipaddress 172.17.22.2/24
2. DGS-1210-28MP/ME:5#config ipif System ipv6 ipv6address 2001:db8:b40:4002::2/64
3. DGS-1210-28MP/ME:5# create iproute default 172.17.22.1
4. DGS-1210-28MP/ME:5# create ipv6route default 2001:db8:b40:4002::1
5. DGS-1210-28MP/ME:5# enable ssh
6. DGS-1210-28MP/ME:5# enable password encryption
7. DGS-1210-28MP/ME:5# create account admin mupsbox
8. DGS-1210-28MP/ME:5# save
Huawei AR100
Minimum* configuration:
BASIC ETHERNET CONFIGURATION - SUMMARY STEPS
1. <Huawei> system-view
2. [Huawei] interface GigabitEthernet 0/0/0
3. [Huawei-GigabitEthernet0/0/0] undo portswhich
4. [Huawei-GigabitEthernet0/0/0] ip address 172.17.22.5 255.255.255.0
5. [Huawei-GigabitEthernet0/0/0] quit
6. [Huawei] ip route-static 0.0.0.0 0.0.0.0 172.17.22.1
7. [Huawei] save
HP Procurve
Minimum* configuration:
BASIC ETHERNET CONFIGURATION - SUMMARY STEPS
1. ProCurve Switch 2510-48# config
2. ProCurve Switch 2510-48(config)# hostname MBHP-2510
3. MBHP-2510(config)# vlan 1
4. MBHP-2510(vlan-1)# ip address 172.17.44.2/24
5. MBHP-2510(vlan-1)# exit
6. MBHP-2510(config)# ip default-gateway 172.17.44.1
BASIC SSH CONFIGURATION - SUMMARY STEPS
7. MBHP-2510(config)# ip ssh
8. MBHP-2510(config)# crypto key generate ssh
9. MBHP-2510(config)# password manager
10. MBHP-2510(config)# aaa authentication login privilege-mode
11. MBHP-2510(config)# aaa authentication ssh login tacacs local
12. MBHP-2510(config)# aaa authentication ssh enable tacacs local
13. MBHP-2510(config)# write memory
Juniper SRX
Minimum* configuration:
BASIC CONFIGURATION - SUMMARY STEPS
1. root@% cli
2. root> configure
3. root# set system host-name MBSRX100b
4. root# set system root-authentication plain-text-password
New password: password
Retype new password: password
5. root# set system login user mupsbox class super-user authentication plain-text-password
6. root# commit
BASIC ETHERNET CONFIGURATION - SUMMARY STEPS
7. root@MBSRX100b# set interfaces fe-0/0/0 unit 0 family inet address 172.17.44.4/24
8. root@MBSRX100b# set routing-options static route 0.0.0.0/0 next-hop 172.17.44.1
9. root@MBSRX100b# delete security zones security-zone untrust interfaces fe-0/0/0
10. root@MBSRX100b# set security zones security-zone internal interfaces fe-0/0/0 host-inbound-traffic system-services ping
11. root@MBSRX100b# set security zones security-zone internal interfaces fe-0/0/0 host-inbound-traffic system-services ssh
12. root@MBSRX100b# commit
Juniper SSG
Minimum* configuration:
BASIC CONFIGURATION - SUMMARY STEPS
1. root-> set hostname MBSSG5
2.MBSSG5-> set admin name mupsbox
3. MBSSG5-> set admin password PassW0rd
4. MBSSG5-> set interface bgroup0 ip 172.17.44.5/24
5. MBSSG5-> set route 0.0.0.0/0 interface bgroup0 gateway 172.17.44.1
6. MBSSG5-> save
7. MBSSG5-> set interface bgroup0 manage ssh
8. MBSSG5-> set ssh enable