Difference between revisions of "Device configuration for MupsBox"

From Mupssoft Wiki
Jump to navigation Jump to search
 
(105 intermediate revisions by the same user not shown)
Line 1: Line 1:
 
<h1>'''Device Configuration'''</h1>
 
<h1>'''Device Configuration'''</h1>
−
<h2>'''How to'''</h2>
+
<h2>'''Introduction'''</h2>
−
<p>The module displays all the logs that were sent to the server on which the MupsBox program is running with the Syslog service installed and running.</p>
+
<p>This section is not a tutorial on configuration different manufacturers. Here you will find the minimum settings in the CLI (for access from MUPSBOX to devices).</p>
−
[[File:syslog-module.png|Syslog Module]]
+
 
−
<p>In order for the module to work, you need to specify the IP address and port on which to receive logs from devices [[Install_and_Basic_Configuration#Syslog|Syslog]]. It is also necessary to install and run the service Syslog [[Install_and_Basic_Configuration#Install_and_Start_services|Install Service]]</p>
+
 
−
<p>On the Router OS, you need to set the sending of logs to the server with the installed MupsBox program:</p>
+
<h2>'''Cisco - IOS v15'''</h2>Minimum* configuration:
−
[[File:syslog-ros-en1.png|Syslog on ROS]]
+
 
−
<p>In System → Logging, select Actions → remote in the Remote Address field, enter the server address with MupsBox, in the Remote Port field, we set the port we specified in Settings → Syslog → Port Syslog Destination in MupsBox.
+
'''BASIC ETHERNET CONFIGURATION - SUMMARY STEPS'''
−
Next, on the router in System → Logging, select Rules:</p>
+
 
−
[[File:syslog-ros-en2.png|Syslog on ROS]]
+
1.    Router> '''enable'''
−
<p>Add the rules that we want to log. If we want to prefix for the convenience of searching and working with data, it is necessary to enclose it in '''#''' signs, as shown in the example above.
+
 
−
After all the settings, the system will start collecting data:</p>
+
2.    Router# '''configure terminal'''
−
[[File:syslog-module.png|Syslog Module]]
+
 
 +
3.    Router(config)# '''interface gigabitethernet''' 0/0
 +
 
 +
4.    Router(config-if)# '''ip adress''' 10.9.90.201 255.255.255.0
 +
 
 +
5.    Router(config-if)# '''ipv6 address''' 2001:db8:B40:4000::101/64
 +
 
 +
6.    Router(config-if)# '''no shutdown'''
 +
 
 +
7.    Router(config-if)# '''exit'''
 +
 
 +
8.    Router(config)# '''ip route 0.0.0.0 0.0.0.0''' 10.9.90.1
 +
 
 +
9.    Router(config)# '''ipv6 route''' ::/0 2001:db8:B40:4000::1
 +
 
 +
'''BASIC SSH CONFIGURATION - SUMMARY STEPS'''
 +
 
 +
10.    Router(config)# '''ip domain name''' domain.local
 +
 
 +
11.    Router(config)# '''hostname''' MBRouter
 +
 
 +
12.    MBRouter(config)# '''crypto key generate rsa modulus 1024'''
 +
 
 +
13.    MBRouter(config)# '''username''' ''root'' privilege 15 '''secret''' ''PassW0rd''
 +
 
 +
14.    MBRouter(config)# '''aaa new-model'''
 +
 
 +
15.    MBRouter(config)# '''line vty 0 4'''
 +
 
 +
16.    MBRouter(config-line)# '''transport input ssh'''
 +
 
 +
17.    MBRouter(config-line)# '''exit'''
 +
 
 +
'''ADDITIONAL CONFIGURATION - SUMMARY STEPS'''
 +
 
 +
18.    MBRouter(config)# '''enable secret''' PassW0rd
 +
 
 +
19.    MBRouter(config)# '''service password-encryption'''
 +
 
 +
20.    MBRouter(config)# '''end'''
 +
 
 +
21.    MBRouter# '''copy running-config startup-config'''
 +
 
 +
 
 +
<p></p>
 +
 
 +
<h2>'''Cisco - IOS L2 v12'''</h2>Minimum* configuration:
 +
 
 +
'''BASIC ETHERNET CONFIGURATION - SUMMARY STEPS'''
 +
 
 +
1.    Switch> '''enable'''
 +
 
 +
2.    Switch# '''configure terminal'''
 +
 
 +
3.    Switch(config)# '''interface vlan 1'''
 +
 
 +
4.    Switch(config-if)# '''ip adress''' 172.17.33.5 255.255.255.0
 +
 
 +
5.    Switch(config-if)# '''exit'''
 +
 
 +
6.    Switch(config)# '''ip default-gateway''' 172.17.33.1
 +
 
 +
'''BASIC SSH CONFIGURATION - SUMMARY STEPS'''
 +
 
 +
7.    Switch(config)# '''ip domain name''' domain.local
 +
 
 +
8.    Switch(config)# '''hostname''' MBSwitch
 +
 
 +
9.    MBSwitch(config)# '''crypto key generate rsa modulus 1024'''
 +
 
 +
10.    MBSwitch(config)# '''username''' ''root'' privilege 15 '''secret''' ''PassW0rd''
 +
 
 +
11.    MBSwitch(config)# '''aaa new-model'''
 +
 
 +
12.    MBSwitch(config)# '''line vty 0 4'''
 +
 
 +
13.    MBSwitch(config-line)# '''transport input ssh'''
 +
 
 +
14.    MBSwitch(config-line)# '''exit'''
 +
 
 +
 
 +
'''ADDITIONAL CONFIGURATION - SUMMARY STEPS'''
 +
 
 +
15.    MBSwitch(config)# '''enable secret''' PassW0rd
 +
 
 +
16.    MBSwitch(config)# '''service password-encryption'''
 +
 
 +
17.    MBSwitch(config)# '''snmp-server community public RO'''
 +
 
 +
18.    MBSwitch(config)# '''end'''
 +
 
 +
19.    MBSwitch# '''copy running-config startup-config'''
 +
 
 +
 
 +
 
 +
 
 +
 
 +
 
 +
<h2>'''Cisco - ASA'''</h2>
 +
<p>Minimum* configuration. ASA Version 8.2(5):</p>
 +
 
 +
'''BASIC ETHERNET CONFIGURATION - SUMMARY STEPS'''
 +
 
 +
1. ciscoasa> '''enable'''
 +
 
 +
2. ciscoasa# '''configure termina'''l
 +
 
 +
3. (config)# '''enable password''' ''mtigroup''
 +
 
 +
4. ciscoasa(config)# '''hostname''' ''MBCiscoasa''
 +
 
 +
5. MBCiscoasa11(config)# '''interface''' ''gigabitEthernet 0/0''
 +
 
 +
6. MBCiscoasa11(config-if)# '''nameif inside'''
 +
 
 +
7. MBCiscoasa11(config-if)# '''ip address''' ''172.18.11.11 255.255.255.0''
 +
 
 +
8. MBCiscoasa11(config-if)# '''no shutdown'''
 +
 
 +
9. MBCiscoasa11(config-if)# '''exit'''
 +
 
 +
10. MBCiscoasa11(config)# '''route inside''' ''0.0.0.0 0.0.0.0 172.18.11.1''
 +
 
 +
 
 +
 
 +
 
 +
 
 +
'''BASIC SSH CONFIGURATION - SUMMARY STEPS'''
 +
 +
11. MBCiscoasa11(config)# '''ssh''' ''172.31.10.0 255.255.255.0'' '''inside'''
 +
 
 +
12. MBCiscoasa11(config)# '''username''' ''mupsbox password PassW0rd privilege 15''
 +
 
 +
13. MBCiscoasa11(config)# '''aaa authentication ssh console LOCAL'''
 +
 
 +
14. MBCiscoasa11(config)# '''write'''
 +
 
 +
 
 +
 
 +
 
 +
 
 +
'''ADDITIONAL CONFIGURATION - SUMMARY STEPS'''
 +
 
 +
 +
 
 +
<h2>'''MikroTik'''</h2>
 +
<p>Minimum configuration for RouterOS V6 (with "zero" configuration)</p><p>'''BASIC ETHERNET CONFIGURATION - SUMMARY STEPS'''</p>
 +
 
 +
1. [admin@MikroTik] > '''ip address add address='''''172.17.22.4/24'' '''interface='''''ether1''
 +
 
 +
2. [admin@MikroTik] > '''ip route add gateway='''''172.17.22.1''
 +
 
 +
3. [admin@MikroTik] > '''ipv6 address add address='''2001:db8:b40:4002::4/64 '''interface='''ether1
 +
 
 +
4. [admin@MikroTik] > '''ipv6 route add gateway='''2001:db8:b40:4002::1
 +
 
 +
5. [admin@MikroTik] > '''system identity set name='''MBMikroTik
 +
 
 +
6. [admin@MBMikroTik] > '''ip service disable telnet,ftp,www,api'''
 +
 
 +
7. [admin@MBMikroTik] > '''user add name='''mupsbox '''password='''PassW0rd '''group='''full
 +
 
 +
8. [admin@MBMikroTik] > '''user remove admin'''<h2>'''DLink DGS'''</h2>
 +
<p>Minimum* configuration:</p>'''BASIC ETHERNET CONFIGURATION - SUMMARY STEPS'''
 +
 
 +
1. DGS-1210-28MP/ME:5# '''config ipif System ipaddress''' 172.17.22.2/24
 +
 
 +
2. DGS-1210-28MP/ME:5#'''config ipif System ipv6 ipv6address''' 2001:db8:b40:4002::2/64
 +
 
 +
3. DGS-1210-28MP/ME:5# '''create iproute default''' 172.17.22.1
 +
 
 +
4. DGS-1210-28MP/ME:5# '''create ipv6route default''' 2001:db8:b40:4002::1
 +
 
 +
5. DGS-1210-28MP/ME:5# '''enable ssh'''
 +
 
 +
6. DGS-1210-28MP/ME:5# '''enable password encryption'''
 +
 
 +
7. DGS-1210-28MP/ME:5# '''create account admin''' mupsbox
 +
 
 +
8. DGS-1210-28MP/ME:5# '''save'''
 +
 
 +
 
 +
<h2>'''Huawei AR100'''</h2>
 +
 
 +
Minimum* configuration:
 +
 
 +
'''BASIC ETHERNET CONFIGURATION - SUMMARY STEPS'''
 +
 
 +
1. <Huawei> '''system-view'''
 +
 
 +
2. [Huawei] '''interface''' ''GigabitEthernet 0/0/0''
 +
 
 +
3. [Huawei-GigabitEthernet0/0/0] '''undo portswitch'''
 +
 
 +
4. [Huawei-GigabitEthernet0/0/0] '''ip address''' ''172.17.22.5 255.255.255.0''
 +
 
 +
5. [Huawei-GigabitEthernet0/0/0] '''quit'''
 +
 
 +
6. [Huawei] '''ip route-static''' '''0.0.0.0 0.0.0.0''' ''172.17.22.1''
 +
 
 +
7. [Huawei] '''save'''
 +
 
 +
 
 +
 
 +
8. [Huawei] '''aaa'''
 +
 
 +
9. [Huawei-aaa] '''local-user''' mupsbox '''password cipher''' PassW0rd
 +
 
 +
10. [Huawei-aaa] '''local-user''' '''admin privilege level 15'''
 +
 
 +
11. [Huawei-aaa] '''local-user admin service-type ssh'''
 +
 
 +
12. [Huawei-aaa] '''quit'''
 +
 
 +
13. [Huawei] '''quit save'''
 +
 
 +
14. [Huawei] '''stelnet server enable'''
 +
 
 +
15. [Huawei] '''save'''
 +
 
 +
<h2>'''Huawei Quidway 2000,3000,5000'''</h2>
 +
 
 +
Minimum* configuration:
 +
 
 +
'''BASIC ETHERNET CONFIGURATION - SUMMARY STEPS'''
 +
 
 +
1. <Quidway> '''system-view'''
 +
 
 +
2. [Quidway]'''management-vlan 1'''
 +
 
 +
3. [Quidway] '''interface Vlan-interface 1'''
 +
 
 +
4. [Quidway-Vlan-interface1] '''ip address''' ''172.17.55.7 255.255.255.0''
 +
 
 +
5. [[Quidway-Vlan-interface1] '''quit'''
 +
 
 +
6. [Quidway] '''ip route-static''' '''0.0.0.0 0.0.0.0''' ''172.17.22.1''
 +
 
 +
7. [Quidway] '''save'''
 +
 
 +
 
 +
 
 +
'''BASIC SSH CONFIGURATION - SUMMARY STEPS'''
 +
 
 +
8. [Quidway] '''user-interface vty 0 4'''
 +
 
 +
9. [Quidway-ui-vty0-4] '''authentication-mode scheme'''
 +
 
 +
10. [Quidway-ui-vty0-4] '''protocol inbound ssh'''
 +
 
 +
11. [Quidway] '''local-user''' ''mupsbox''
 +
 
 +
12. [Quidway-luser-mupsbox] '''password simple''' ''PassW0rd''
 +
 
 +
13. [Quidway-luser-mupsbox] '''service-type ssh'''
 +
 
 +
14. [Quidway] '''ssh user''' ''mupsbox'' '''authentication-type password'''
 +
 
 +
15. [Quidway] '''rsa local-key-pair create'''
 +
 
 +
16. [Quidway] '''save'''
 +
 +
 
 +
 
 +
 
 +
<h2>'''HP Procurve'''</h2>
 +
 
 +
Minimum* configuration:
 +
 
 +
'''BASIC ETHERNET CONFIGURATION - SUMMARY STEPS'''
 +
 
 +
1. ProCurve Switch 2510-48# '''config'''
 +
 
 +
2. ProCurve Switch 2510-48(config)# '''hostname''' ''MBHP-2510''
 +
 
 +
3. MBHP-2510(config)# '''vlan 1'''
 +
 
 +
4. MBHP-2510(vlan-1)# '''ip address''' ''172.17.44.2/24''
 +
 
 +
5. MBHP-2510(vlan-1)# '''exit'''
 +
 
 +
6. MBHP-2510(config)# '''ip default-gateway''' ''172.17.44.1''
 +
 
 +
 
 +
 
 +
 
 +
 
 +
'''BASIC SSH CONFIGURATION - SUMMARY STEPS'''
 +
 
 +
7. MBHP-2510(config)# '''ip ssh'''
 +
 
 +
8. MBHP-2510(config)# '''crypto key generate ssh'''
 +
 
 +
9. MBHP-2510(config)# '''password manager'''
 +
 
 +
10. MBHP-2510(config)# '''aaa authentication login privilege-mode'''
 +
 
 +
11. MBHP-2510(config)# '''aaa authentication ssh login tacacs local'''
 +
 
 +
12. MBHP-2510(config)# '''aaa authentication ssh enable tacacs local'''
 +
 
 +
13. MBHP-2510(config)# '''write memory'''
 +
 
 +
 
 +
<h2>'''Juniper SRX'''</h2>
 +
 
 +
Minimum* configuration:
 +
 
 +
'''BASIC CONFIGURATION - SUMMARY STEPS'''
 +
 
 +
1. root@% '''cli'''
 +
 
 +
2. root> '''configure'''
 +
 
 +
3. root# '''set system host-name''' ''MBSRX100b''
 +
 
 +
4. root# <kbd>'''set system root-authentication plain-text-password'''</kbd>
 +
 
 +
''New password: <var>password</var>''
 +
 
 +
''Retype new password: <var>password</var>''
 +
 
 +
5. root# <kbd>'''set system login user''' ''mupsbox'' '''class super-user authentication plain-text-password'''</kbd>
 +
 
 +
6. root# '''commit'''
 +
 
 +
 
 +
 
 +
'''BASIC ETHERNET CONFIGURATION - SUMMARY STEPS'''
 +
 
 +
7. root@MBSRX100b#  '''set interfaces''' ''fe-0/0/0'' '''unit 0 family inet address''' <var>172.17.44.4/24</var>
 +
 
 +
8. root@MBSRX100b# '''set routing-options static route''' '''0.0.0.0/0 next-hop''' 172.17.44.1
 +
 
 +
9. root@MBSRX100b# '''delete security zones security-zone untrust interfaces''' ''fe-0/0/0''
 +
 
 +
10. root@MBSRX100b# '''set security zones security-zone internal interfaces''' ''fe-0/0/0'' '''host-inbound-traffic system-services ping'''
 +
 
 +
11. root@MBSRX100b# '''set security zones security-zone internal interfaces''' ''fe-0/0/0'' '''host-inbound-traffic system-services ssh'''
 +
 
 +
12. root@MBSRX100b# '''set system services ssh'''
 +
 
 +
13. root@MBSRX100b# '''set system services ssh root-login allow'''
 +
 
 +
12. root@MBSRX100b# '''commit'''
 +
 
 +
 
 +
<h2>'''Juniper ES'''</h2>
 +
 
 +
Minimum* configuration:
 +
 
 +
'''BASIC CONFIGURATION - SUMMARY STEPS'''
 +
 
 +
1. root@% '''cli'''
 +
 
 +
2. root> '''configure'''
 +
 
 +
3. root# '''set system host-name''' MBSRX100b
 +
 
 +
4. root# <kbd>'''set system root-authentication plain-text-password'''</kbd>
 +
 
 +
''New password: <var>password</var>''
 +
 
 +
''Retype new password: <var>password</var>''
 +
 
 +
5. root# <kbd>'''set system login user''' ''mupsbox'' '''class super-user authentication plain-text-password'''</kbd>
 +
 
 +
6. root# '''commit'''
 +
 
 +
 
 +
 
 +
'''BASIC ETHERNET CONFIGURATION - SUMMARY STEPS'''
 +
 
 +
7. root@MBSRX100b#  delete interface ge-0/0/0 unit 0 family ethernet-switching
 +
 
 +
8. root@MBSRX100b#  '''set interfaces''' ge-0/0/0 '''unit 0 family inet address''' <var>172.17.44.4/24</var>
 +
 
 +
9. root@MBSRX100b# '''set routing-options static route''' '''0.0.0.0/0 next-hop''' 172.17.44.1
 +
 
 +
10. root@MBSRX100b# '''set system services ssh'''
 +
 
 +
11. root@MBSRX100b# '''set system services ssh connection-limit 10 rate-limit 4'''
 +
 
 +
12. root@MBSRX100b# '''commit'''
 +
 
 +
 
 +
 
 +
<h2>'''Juniper SSG'''</h2>
 +
 
 +
Minimum* configuration:
 +
 
 +
'''BASIC  CONFIGURATION - SUMMARY STEPS'''
 +
 
 +
1. root-> '''set hostname''' ''MBSSG5''
 +
 
 +
2. MBSSG5-> '''set admin name''' ''mupsbox''
 +
 
 +
3. MBSSG5-> '''set admin password''' ''PassW0rd''
 +
 
 +
4. MBSSG5-> <kbd>'''set interface''' ''bgroup0'' '''ip 172.17.44.5/24'''</kbd>
 +
 
 +
5. MBSSG5-> '''set route''' ''0.0.0.0/0'' '''interface''' ''bgroup0'' '''gateway''' ''172.17.44.1''
 +
 
 +
6. MBSSG5-> '''save'''
 +
 
 +
7. MBSSG5-> '''set interface''' ''bgroup0'' '''manage ssh'''
 +
 
 +
8. MBSSG5-> '''set ssh enable'''
 +
 
 +
 
 +
 
 +
 
 +
<h2>'''Eltex  MES'''</h2>
 +
 
 +
Minimum* configuration:
 +
 
 +
'''BASIC  CONFIGURATION - SUMMARY STEPS'''
 +
 
 +
1. console> '''enable'''
 +
 
 +
2. console# '''configure'''
 +
 
 +
2. console(config)# '''interface vlan 1'''
 +
 
 +
3. console(config-if)# '''no ip address dhcp'''
 +
 
 +
4. console(config-if)# '''ip address''' ''172.17.55.4 255.255.255.0''
 +
 
 +
5. console(config-if)# '''exit'''
 +
 
 +
6. console(config)# '''ip route''' ''0.0.0.0 0.0.0.0 172.17.55.1''
 +
 
 +
7. console(config)# '''hostname''' ''MBEltexMES''
 +
 
 +
8. console(config)# '''ip ssh server'''
 +
 
 +
9. MBEltexMES(config)# '''username''' ''mupsbox'' ''privilege 15'' '''password''' ''PassW0rd!''
 +
 
 +
10. MBEltexMES(config)# '''enable password prpassword'''
 +
 
 +
 
 +
 
 +
 
 +
<h2>'''Zyxel ZyWALL'''</h2>
 +
 
 +
Minimum* configuration:
 +
 
 +
'''BASIC  CONFIGURATION - SUMMARY STEPS'''
 +
 
 +
1. Router> '''enable'''
 +
 
 +
2. Router# '''configure terminal'''
 +
 
 +
2. Router(config)# '''interface''' ''ge2''
 +
 
 +
3. Router(config-if-ge)# '''ip address''' ''172.17.44.7 255.255.255.0''
 +
 
 +
4. Router(config-if-ge)# '''ip gateway''' ''172.17.44.1''
 +
 
 +
5. Router(config-if-ge)# '''no shutdown'''
 +
 
 +
6. Router(config-if-ge)# '''exit'''
 +
 
 +
7. Router(config)# '''username''' ''mupsbox'' '''password''' ''PassW0rd'' '''user-type''' ''admin''
 +
 
 +
 
 +
 
 +
 
 +
<h2>'''Qtech QSW'''</h2>
 +
 
 +
Minimum* configuration:
 +
 
 +
'''BASIC  CONFIGURATION - SUMMARY STEPS'''
 +
 
 +
1. QSW-2850-28T-AC> '''enable'''
 +
 
 +
2. QSW-2850-28T-AC# '''config terminal'''
 +
 
 +
2. QSW-2850-28T-AC(config)# '''interface vlan 1'''
 +
 
 +
3. QSW-2850-28T-AC(config-if-vlan1)# '''ip address''' ''172.17.44.8 255.255.255.0''
 +
 
 +
4. QSW-2850-28T-AC(config-if-vlan1)# '''exit'''
 +
 
 +
5. QSW-2850-28T-AC(config)# '''ip default-gateway''' ''172.17.44.1''
 +
 
 +
6. QSW-2850-28T-AC(config)# '''ssh-server enable'''
 +
 
 +
7. QSW-2850-28T-AC(config)# '''username''' ''mupsbox'' privilege 15 '''password''' ''PassW0rd''
 +
 
 +
8. QSW-2850-28T-AC(config)# '''exit'''
 +
 
 +
9. QSW-2850-28T-AC# '''copy running-config startup-config'''
 +
 
 +
 
 +
 
 +
 
 +
<h2>'''Allied Telesis'''</h2>
 +
 
 +
Minimum* configuration:
 +
 
 +
'''BASIC  CONFIGURATION - SUMMARY STEPS'''
 +
 
 +
1. console# '''config'''
 +
 
 +
2. console(config)# '''interface vlan 1'''
 +
 
 +
3. console(config-if)# '''ip address''' ''172.17.55.9 255.255.255.0''
 +
 
 +
4.console(config-if)# '''exit'''
 +
 
 +
5. console(config)# '''ip default-gateway''' ''172.17.55.1''
 +
 
 +
6. console(config)# '''username''' ''mupsbox'' '''password''' ''PassW0rd'' level 15
 +
 
 +
7. console(config)# '''ip ssh server'''
 +
 
 +
8. console(config)# '''crypto key generate rsa'''
 +
 
 +
 
 +
 
 +
<h2>'''Fortinet'''</h2>
 +
 
 +
Minimum* configuration:
 +
 
 +
'''BASIC  CONFIGURATION - SUMMARY STEPS'''
 +
 
 +
1. FortiGate-VM64-KVM # '''config system interface'''
 +
 
 +
2. FortiGate-VM64-KVM (interface) # '''edit''' ''port1''
 +
 
 +
2. FortiGate-VM64-KVM (port1) # '''set ip''' ''172.18.33.111 255.255.255.0''
 +
 
 +
3 FortiGate-VM64-KVM (port1) # '''end'''
 +
 
 +
4. FortiGate-VM64-KVM # '''config router static'''
 +
 
 +
5. FortiGate-VM64-KVM (static) # '''edit''' ''0''
 +
 
 +
6. FortiGate-VM64-KVM (0) # '''set gateway''' ''172.18.33.1''
 +
 
 +
7. FortiGate-VM64-KVM (0) # '''set device''' ''port1''
 +
 
 +
8. FortiGate-VM64-KVM (0) # '''end'''
 +
 
 +
9. FortiGate-VM64-KVM # '''config system admin'''
 +
 
 +
10. FortiGate-VM64-KVM (admin) # '''edit''' ''mupsbox''
 +
 
 +
11. FortiGate-VM64-KVM (mupsbox) # '''set accprofile''' ''"super_admin"''
 +
 
 +
12. FortiGate-VM64-KVM (mupsbox) # '''set vdom "root"'''
 +
 
 +
13. FortiGate-VM64-KVM (mupsbox) # '''set password''' ''PassW0rd''
 +
 
 +
14. FortiGate-VM64-KVM (mupsbox) # '''end'''
 +
 
 +
15. FortiGate-VM64-KVM # '''config system global'''
 +
 
 +
16. FortiGate-VM64-KVM (global) # '''set hostname''' ''FortiGateV''
 +
 
 +
17. FortiGate-VM64-KVM (global) # '''end'''
 +
 
 +
18. FortiGateV # '''execute cfg save'''
 +
 
 +
 
 +
 
 +
<h2>'''Extreme Networks'''</h2>
 +
 
 +
Minimum* configuration:
 +
 
 +
'''BASIC  CONFIGURATION - SUMMARY STEPS'''
 +
 
 +
1. * EXOS-VM.1 # '''create account admin''' ''mupsbox'' ''PassW0rd''
 +
 
 +
2. * EXOS-VM.6 # '''configure''' ''Mgmt'' '''ipaddress''' ''172.18.33.222 255.255.255.0''
 +
 
 +
3. * EXOS-VM.9 # '''configure iproute add default''' ''172.18.33.1'' '''vr''' ''VR-Mgmt''
 +
 
 +
4.* EXOS-VM.11 # '''enable ssh2'''
 +
 
 +
5.* EXOS-VM.11 # '''save'''
 +
 
 +
 
 +
 
 +
 
 +
<h2>'''Check Point'''</h2>
 +
 
 +
Minimum* configuration:
 +
 
 +
'''BASIC  CONFIGURATION - SUMMARY STEPS'''
 +
 
 +
1. gw-170003>set expert-password
 +
 
 +
2.gw-170003>expert
 +
 
 +
3. [Expert@gw-170003:0]# hostname MBCheckPoint
 +
 
 +
4.[Expert@MBCheckPoint]# hostname MBCheckPoint
 +
 
 +
5.* EXOS-VM.11 # save
 +
 
 +
 
 +
 
 +
 
 +
 
 +
 
 +
 
 +
<br><br><div id="BackToTop" class="noprint" style="background-color:#DDEFDD; position:fixed;
 +
 
  
−
<p><ul>
 
−
There are 3 buttons on the Syslog tab: update data manually, export to excel and delete all to.
 
−
Also, a powerful tool is built into Syslog to filter data by conditions or/and by certain data:
 
−
<li>[[File:refresh.png|Refresh]] - Refresh syslog snapshots history<br></li>
 
−
<li>[[File:exel.png|Export the visible list of logs in Excel]] - Export the visible list of logs in Excel<br></li>
 
−
<li>[[File:kill-treads.png|Delete all]] - Delete all data<br></li>
 
−
<li>Date filter - Filtering by the specified period of days<br></li>
 
−
<li>Time filter - Filtering by a given time period<br></li>
 
−
<li>Auto update - Auto update of the list of logs for a given period in seconds.<br></li>
 
−
</ul></p>
 
  
−
<h2>'''Filter and search'''</h2>
 
−
<h3>'''Search by Keyword'''</h3>
 
−
<p>If you need to find a log line by keyword, type it in the search field:</p>
 
−
[[File:syslog-search.png|Syslog Search]]
 
−
<p>MupsBox will sort the data and display only the values found. These data can be exported to Excel for further processing.</p>
 
−
<h3>'''Search by Date or/and Time'''</h3>
 
−
<p>To search for data by given dates and times, check the boxes next to them and select the date and time you are interested in:</p>
 
−
[[File:syslog-datetime.png|Syslog Filter by Date and Time]]
 
−
<h3>'''Filter by Prefix, Device and Topics'''</h3>
 
−
<p>To filter by prefix, click the down arrow in the prefix field, as shown in the figure below and select the prefix or prefixes by which you need to filter the data.</p>
 
−
[[File:syslog-prefix.png|Syslog Filter by Prefix]]
 
−
<p>To filter by device and topic, do the same.</p>
 
−
<h3>'''Custom Filter'''</h3>
 
−
<p>For more flexible filtering, use a custom filter.</p>
 
−
[[File:custom-filter.png|Custom Filter]]<br><br>
 
−
[[File:custom-filter2.png|Custom Filter]]
 
−
<div id="BackToTop"  class="noprint" style="background-color:#DDEFDD; position:fixed;
 
 
  bottom:32px; left:2%; z-index:9999; padding:0; margin:0;"><span style="color:blue;
 
  bottom:32px; left:2%; z-index:9999; padding:0; margin:0;"><span style="color:blue;
 
  font-size:8pt; font-face:verdana,sans-serif;  border:0.2em outset #ceebf7;
 
  font-size:8pt; font-face:verdana,sans-serif;  border:0.2em outset #ceebf7;
 
  padding:0.1em; font-weight:bolder; -moz-border-radius:8px; ">
 
  padding:0.1em; font-weight:bolder; -moz-border-radius:8px; ">
−
[[#top| Back to the Top ]]</span></div>
+
[[#top| Back to the Top]]</span></div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div>
 +
<div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div>
 +
<div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div><div id="turnkey-credit"> <div style="clear: both;"> [https://www.turnkeylinux.org/mediawiki MediaWiki Appliance] - Powered by [https://www.turnkeylinux.org TurnKey Linux] </div> </div>

Latest revision as of 03:45, 22 June 2021

Device Configuration

Introduction

This section is not a tutorial on configuration different manufacturers. Here you will find the minimum settings in the CLI (for access from MUPSBOX to devices).


Cisco - IOS v15

Minimum* configuration:

BASIC ETHERNET CONFIGURATION - SUMMARY STEPS

1. Router> enable

2. Router# configure terminal

3. Router(config)# interface gigabitethernet 0/0

4. Router(config-if)# ip adress 10.9.90.201 255.255.255.0

5. Router(config-if)# ipv6 address 2001:db8:B40:4000::101/64

6. Router(config-if)# no shutdown

7. Router(config-if)# exit

8. Router(config)# ip route 0.0.0.0 0.0.0.0 10.9.90.1

9. Router(config)# ipv6 route ::/0 2001:db8:B40:4000::1

BASIC SSH CONFIGURATION - SUMMARY STEPS

10. Router(config)# ip domain name domain.local

11. Router(config)# hostname MBRouter

12. MBRouter(config)# crypto key generate rsa modulus 1024

13. MBRouter(config)# username root privilege 15 secret PassW0rd

14. MBRouter(config)# aaa new-model

15. MBRouter(config)# line vty 0 4

16. MBRouter(config-line)# transport input ssh

17. MBRouter(config-line)# exit

ADDITIONAL CONFIGURATION - SUMMARY STEPS

18. MBRouter(config)# enable secret PassW0rd

19. MBRouter(config)# service password-encryption

20. MBRouter(config)# end

21. MBRouter# copy running-config startup-config


Cisco - IOS L2 v12

Minimum* configuration:

BASIC ETHERNET CONFIGURATION - SUMMARY STEPS

1. Switch> enable

2. Switch# configure terminal

3. Switch(config)# interface vlan 1

4. Switch(config-if)# ip adress 172.17.33.5 255.255.255.0

5. Switch(config-if)# exit

6. Switch(config)# ip default-gateway 172.17.33.1

BASIC SSH CONFIGURATION - SUMMARY STEPS

7. Switch(config)# ip domain name domain.local

8. Switch(config)# hostname MBSwitch

9. MBSwitch(config)# crypto key generate rsa modulus 1024

10. MBSwitch(config)# username root privilege 15 secret PassW0rd

11. MBSwitch(config)# aaa new-model

12. MBSwitch(config)# line vty 0 4

13. MBSwitch(config-line)# transport input ssh

14. MBSwitch(config-line)# exit


ADDITIONAL CONFIGURATION - SUMMARY STEPS

15. MBSwitch(config)# enable secret PassW0rd

16. MBSwitch(config)# service password-encryption

17. MBSwitch(config)# snmp-server community public RO

18. MBSwitch(config)# end

19. MBSwitch# copy running-config startup-config




Cisco - ASA

Minimum* configuration. ASA Version 8.2(5):

BASIC ETHERNET CONFIGURATION - SUMMARY STEPS

1. ciscoasa> enable

2. ciscoasa# configure terminal

3. (config)# enable password mtigroup

4. ciscoasa(config)# hostname MBCiscoasa

5. MBCiscoasa11(config)# interface gigabitEthernet 0/0

6. MBCiscoasa11(config-if)# nameif inside

7. MBCiscoasa11(config-if)# ip address 172.18.11.11 255.255.255.0

8. MBCiscoasa11(config-if)# no shutdown

9. MBCiscoasa11(config-if)# exit

10. MBCiscoasa11(config)# route inside 0.0.0.0 0.0.0.0 172.18.11.1



BASIC SSH CONFIGURATION - SUMMARY STEPS

11. MBCiscoasa11(config)# ssh 172.31.10.0 255.255.255.0 inside

12. MBCiscoasa11(config)# username mupsbox password PassW0rd privilege 15

13. MBCiscoasa11(config)# aaa authentication ssh console LOCAL

14. MBCiscoasa11(config)# write



ADDITIONAL CONFIGURATION - SUMMARY STEPS


MikroTik

Minimum configuration for RouterOS V6 (with "zero" configuration)

BASIC ETHERNET CONFIGURATION - SUMMARY STEPS

1. [admin@MikroTik] > ip address add address=172.17.22.4/24 interface=ether1

2. [admin@MikroTik] > ip route add gateway=172.17.22.1

3. [admin@MikroTik] > ipv6 address add address=2001:db8:b40:4002::4/64 interface=ether1

4. [admin@MikroTik] > ipv6 route add gateway=2001:db8:b40:4002::1

5. [admin@MikroTik] > system identity set name=MBMikroTik

6. [admin@MBMikroTik] > ip service disable telnet,ftp,www,api

7. [admin@MBMikroTik] > user add name=mupsbox password=PassW0rd group=full

8. [admin@MBMikroTik] > user remove admin

DLink DGS

Minimum* configuration:

BASIC ETHERNET CONFIGURATION - SUMMARY STEPS

1. DGS-1210-28MP/ME:5# config ipif System ipaddress 172.17.22.2/24

2. DGS-1210-28MP/ME:5#config ipif System ipv6 ipv6address 2001:db8:b40:4002::2/64

3. DGS-1210-28MP/ME:5# create iproute default 172.17.22.1

4. DGS-1210-28MP/ME:5# create ipv6route default 2001:db8:b40:4002::1

5. DGS-1210-28MP/ME:5# enable ssh

6. DGS-1210-28MP/ME:5# enable password encryption

7. DGS-1210-28MP/ME:5# create account admin mupsbox

8. DGS-1210-28MP/ME:5# save


Huawei AR100

Minimum* configuration:

BASIC ETHERNET CONFIGURATION - SUMMARY STEPS

1. <Huawei> system-view

2. [Huawei] interface GigabitEthernet 0/0/0

3. [Huawei-GigabitEthernet0/0/0] undo portswitch

4. [Huawei-GigabitEthernet0/0/0] ip address 172.17.22.5 255.255.255.0

5. [Huawei-GigabitEthernet0/0/0] quit

6. [Huawei] ip route-static 0.0.0.0 0.0.0.0 172.17.22.1

7. [Huawei] save


8. [Huawei] aaa

9. [Huawei-aaa] local-user mupsbox password cipher PassW0rd

10. [Huawei-aaa] local-user admin privilege level 15

11. [Huawei-aaa] local-user admin service-type ssh

12. [Huawei-aaa] quit

13. [Huawei] quit save

14. [Huawei] stelnet server enable

15. [Huawei] save

Huawei Quidway 2000,3000,5000

Minimum* configuration:

BASIC ETHERNET CONFIGURATION - SUMMARY STEPS

1. <Quidway> system-view

2. [Quidway]management-vlan 1

3. [Quidway] interface Vlan-interface 1

4. [Quidway-Vlan-interface1] ip address 172.17.55.7 255.255.255.0

5. [[Quidway-Vlan-interface1] quit

6. [Quidway] ip route-static 0.0.0.0 0.0.0.0 172.17.22.1

7. [Quidway] save


BASIC SSH CONFIGURATION - SUMMARY STEPS

8. [Quidway] user-interface vty 0 4

9. [Quidway-ui-vty0-4] authentication-mode scheme

10. [Quidway-ui-vty0-4] protocol inbound ssh

11. [Quidway] local-user mupsbox

12. [Quidway-luser-mupsbox] password simple PassW0rd

13. [Quidway-luser-mupsbox] service-type ssh

14. [Quidway] ssh user mupsbox authentication-type password

15. [Quidway] rsa local-key-pair create

16. [Quidway] save



HP Procurve

Minimum* configuration:

BASIC ETHERNET CONFIGURATION - SUMMARY STEPS

1. ProCurve Switch 2510-48# config

2. ProCurve Switch 2510-48(config)# hostname MBHP-2510

3. MBHP-2510(config)# vlan 1

4. MBHP-2510(vlan-1)# ip address 172.17.44.2/24

5. MBHP-2510(vlan-1)# exit

6. MBHP-2510(config)# ip default-gateway 172.17.44.1



BASIC SSH CONFIGURATION - SUMMARY STEPS

7. MBHP-2510(config)# ip ssh

8. MBHP-2510(config)# crypto key generate ssh

9. MBHP-2510(config)# password manager

10. MBHP-2510(config)# aaa authentication login privilege-mode

11. MBHP-2510(config)# aaa authentication ssh login tacacs local

12. MBHP-2510(config)# aaa authentication ssh enable tacacs local

13. MBHP-2510(config)# write memory


Juniper SRX

Minimum* configuration:

BASIC CONFIGURATION - SUMMARY STEPS

1. root@% cli

2. root> configure

3. root# set system host-name MBSRX100b

4. root# set system root-authentication plain-text-password

New password: password

Retype new password: password

5. root# set system login user mupsbox class super-user authentication plain-text-password

6. root# commit


BASIC ETHERNET CONFIGURATION - SUMMARY STEPS

7. root@MBSRX100b# set interfaces fe-0/0/0 unit 0 family inet address 172.17.44.4/24

8. root@MBSRX100b# set routing-options static route 0.0.0.0/0 next-hop 172.17.44.1

9. root@MBSRX100b# delete security zones security-zone untrust interfaces fe-0/0/0

10. root@MBSRX100b# set security zones security-zone internal interfaces fe-0/0/0 host-inbound-traffic system-services ping

11. root@MBSRX100b# set security zones security-zone internal interfaces fe-0/0/0 host-inbound-traffic system-services ssh

12. root@MBSRX100b# set system services ssh

13. root@MBSRX100b# set system services ssh root-login allow

12. root@MBSRX100b# commit


Juniper ES

Minimum* configuration:

BASIC CONFIGURATION - SUMMARY STEPS

1. root@% cli

2. root> configure

3. root# set system host-name MBSRX100b

4. root# set system root-authentication plain-text-password

New password: password

Retype new password: password

5. root# set system login user mupsbox class super-user authentication plain-text-password

6. root# commit


BASIC ETHERNET CONFIGURATION - SUMMARY STEPS

7. root@MBSRX100b# delete interface ge-0/0/0 unit 0 family ethernet-switching

8. root@MBSRX100b# set interfaces ge-0/0/0 unit 0 family inet address 172.17.44.4/24

9. root@MBSRX100b# set routing-options static route 0.0.0.0/0 next-hop 172.17.44.1

10. root@MBSRX100b# set system services ssh

11. root@MBSRX100b# set system services ssh connection-limit 10 rate-limit 4

12. root@MBSRX100b# commit


Juniper SSG

Minimum* configuration:

BASIC CONFIGURATION - SUMMARY STEPS

1. root-> set hostname MBSSG5

2. MBSSG5-> set admin name mupsbox

3. MBSSG5-> set admin password PassW0rd

4. MBSSG5-> set interface bgroup0 ip 172.17.44.5/24

5. MBSSG5-> set route 0.0.0.0/0 interface bgroup0 gateway 172.17.44.1

6. MBSSG5-> save

7. MBSSG5-> set interface bgroup0 manage ssh

8. MBSSG5-> set ssh enable



Eltex MES

Minimum* configuration:

BASIC CONFIGURATION - SUMMARY STEPS

1. console> enable

2. console# configure

2. console(config)# interface vlan 1

3. console(config-if)# no ip address dhcp

4. console(config-if)# ip address 172.17.55.4 255.255.255.0

5. console(config-if)# exit

6. console(config)# ip route 0.0.0.0 0.0.0.0 172.17.55.1

7. console(config)# hostname MBEltexMES

8. console(config)# ip ssh server

9. MBEltexMES(config)# username mupsbox privilege 15 password PassW0rd!

10. MBEltexMES(config)# enable password prpassword



Zyxel ZyWALL

Minimum* configuration:

BASIC CONFIGURATION - SUMMARY STEPS

1. Router> enable

2. Router# configure terminal

2. Router(config)# interface ge2

3. Router(config-if-ge)# ip address 172.17.44.7 255.255.255.0

4. Router(config-if-ge)# ip gateway 172.17.44.1

5. Router(config-if-ge)# no shutdown

6. Router(config-if-ge)# exit

7. Router(config)# username mupsbox password PassW0rd user-type admin



Qtech QSW

Minimum* configuration:

BASIC CONFIGURATION - SUMMARY STEPS

1. QSW-2850-28T-AC> enable

2. QSW-2850-28T-AC# config terminal

2. QSW-2850-28T-AC(config)# interface vlan 1

3. QSW-2850-28T-AC(config-if-vlan1)# ip address 172.17.44.8 255.255.255.0

4. QSW-2850-28T-AC(config-if-vlan1)# exit

5. QSW-2850-28T-AC(config)# ip default-gateway 172.17.44.1

6. QSW-2850-28T-AC(config)# ssh-server enable

7. QSW-2850-28T-AC(config)# username mupsbox privilege 15 password PassW0rd

8. QSW-2850-28T-AC(config)# exit

9. QSW-2850-28T-AC# copy running-config startup-config



Allied Telesis

Minimum* configuration:

BASIC CONFIGURATION - SUMMARY STEPS

1. console# config

2. console(config)# interface vlan 1

3. console(config-if)# ip address 172.17.55.9 255.255.255.0

4.console(config-if)# exit

5. console(config)# ip default-gateway 172.17.55.1

6. console(config)# username mupsbox password PassW0rd level 15

7. console(config)# ip ssh server

8. console(config)# crypto key generate rsa


Fortinet

Minimum* configuration:

BASIC CONFIGURATION - SUMMARY STEPS

1. FortiGate-VM64-KVM # config system interface

2. FortiGate-VM64-KVM (interface) # edit port1

2. FortiGate-VM64-KVM (port1) # set ip 172.18.33.111 255.255.255.0

3 FortiGate-VM64-KVM (port1) # end

4. FortiGate-VM64-KVM # config router static

5. FortiGate-VM64-KVM (static) # edit 0

6. FortiGate-VM64-KVM (0) # set gateway 172.18.33.1

7. FortiGate-VM64-KVM (0) # set device port1

8. FortiGate-VM64-KVM (0) # end

9. FortiGate-VM64-KVM # config system admin

10. FortiGate-VM64-KVM (admin) # edit mupsbox

11. FortiGate-VM64-KVM (mupsbox) # set accprofile "super_admin"

12. FortiGate-VM64-KVM (mupsbox) # set vdom "root"

13. FortiGate-VM64-KVM (mupsbox) # set password PassW0rd

14. FortiGate-VM64-KVM (mupsbox) # end

15. FortiGate-VM64-KVM # config system global

16. FortiGate-VM64-KVM (global) # set hostname FortiGateV

17. FortiGate-VM64-KVM (global) # end

18. FortiGateV # execute cfg save


Extreme Networks

Minimum* configuration:

BASIC CONFIGURATION - SUMMARY STEPS

1. * EXOS-VM.1 # create account admin mupsbox PassW0rd

2. * EXOS-VM.6 # configure Mgmt ipaddress 172.18.33.222 255.255.255.0

3. * EXOS-VM.9 # configure iproute add default 172.18.33.1 vr VR-Mgmt

4.* EXOS-VM.11 # enable ssh2

5.* EXOS-VM.11 # save



Check Point

Minimum* configuration:

BASIC CONFIGURATION - SUMMARY STEPS

1. gw-170003>set expert-password

2.gw-170003>expert

3. [Expert@gw-170003:0]# hostname MBCheckPoint

4.[Expert@MBCheckPoint]# hostname MBCheckPoint

5.* EXOS-VM.11 # save






Retrieved from "https://wiki.mupssoft.com/index.php?title=Device_configuration_for_MupsBox&oldid=1084"